• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSX A380 Wing Modeling

Messages
19
Country
germany
Hi,
I have a big problem i am now finished with the Fuselage of my Plane and today i want to make the Wings.
But my problem is that i don't see the wings really on my Blueprint so anybody of you know a good Blueprint side where i see the form from the Left or a good tutorial for making one. I watched some on YouTube they said i must use a line is that correct?
Here is my actual blueprint http://drawingdatabase.com/wp-content/uploads/2014/04/A380-800v1.0.png
Thanks for you help
Regards Max
 
What are you using for a modeling program? Have you properly setup your drawings? Can you send a picture of what you have done so far?
 
My method of creating a wing.
First make a spline of the wing section near the root. Copy this and move it out to the first section of the wing and scale it down. Make another copy of the spline and move it near the tip. Then select the first spline and attach the second and third ones. Use the spline cross section to connect them all. Then add a surface modifier to the stack.
I have made four screen grabs from Max here https://drive.google.com/folderview?id=0B6_seKRK-rv8ZmJRVVZ6WS1na3c&usp=sharing look at them and let me know when you have because I will delete them after.
I hope this helps and gets you started on that wing.
 
If you use Paul's method, when you get to the Surface modifier, reduce the modifier's Threshold setting to zero before panicking that it's not working. ;)
 
Best to attach 1 spline add the cross section from the modifier list then select the 2 splines and then attach more splines 1 at a time. Because the cross section will not align correctly and then when you add surface from the modifier list the wing will not create surface for the entire wing due to the cross sections not having the same amount of lines.
 
Best to attach 1 spline add the cross section from the modifier list then select the 2 splines and then attach more splines 1 at a time. Because the cross section will not align correctly and then when you add surface from the modifier list the wing will not create surface for the entire wing due to the cross sections not having the same amount of lines.

Sorry DG, I've lost you. Could you illustrate that please?
 
Just saying if you have like 5 splines, only attach 2 splines then add the cross section tool. Then attach the other splines.
It will prevent the cross section from adding more lines than is needed!
 
It is important that the vertices in each spline section be numbered in the same order as the next section that you will add a cross section to. Imagine two circles with 4 vertices numbered clockwise 1, 2, 3 and 4 and one circle has number 1 at the 12:00 o'clock position and the second circle has number 1 at the 3:00 o'clock position. The cross section will draw the lines from each numbered vertex to its respective number in the opposing spline section. You should get the idea what would happen. In Max the yellow vertex is the number one vertex in the spline. You can turn on the display of numbers by ticking the (Show Vertex Numbers) in the (Display) dialog. By right clicking on a vertex you can set it as number 1 by clicking on (Make First). You can also reverse the numbering order should one spline be clock wise and the other anti-clockwise. I hope this helps.
 
Another method of creating wings is using airfoils. Whilst the A380 does not have a discrete foil you can use these images below to get the main shape of the wing.

http://airfoiltools.com/airfoil/details?airfoil=sc20610-il

http://airfoiltools.com/airfoil/details?airfoil=sc20606-il

The fist airfoil (sc20610) goes where the fuselage meets the wing and the second (sc20606) goes at the wingtip, you can create them as splines as mention above and then when converted to an editable poly you can add extra rings and scale/move them to make the proper wing shape.
 
I make an outline of the airfoil with a Spline. I use Bezier and make it very nicely rounded and proper. This is a template. Next, I make the sections that are in the wing, the aileron shape (airfoil), the wing shape (that has the inlet for the leading edge around the aileron front edge). Next I join the aileron (or flap) to the wing, save those as a Editable Poly, then extrude them out. Then use one or two sets of FFD X2 to set rake and dyhedral. Collapse as Editable Poly again. Done. I use a cutting tool like Swift Loop (Max) to add cross sections. Quick and clean, takes like a minute to make a wing shape with its ailerons / flaps already molded in. Done. Mind you, you will have a ton of work after that, wing tips, detaching parts, animating, mapping, but this gives you instant wings with premade ailerons in it.
 
Back
Top