• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Contact Point Settings

Messages
69
Country
ca-newbrunswick
AIrcraft was modeled with FSDS for FS2004. When viewed in FS, The main gear was burried in the ground about 1/3 of the way to the axle. Nosegear was also burried so that the tire was buried up to the rim. I also noticed in slew mode, the whole fuselage tilted so that the nosewheel was clear of the ground by about two feet. when leaving slew mode, the nose slammed back down to where it originally was. I reset the contact points so that the main gear tire bottoms and nosegear tire bottom is just barely below the ground level to produce a very slight flattening effect. Now when going into slew mode all seems ok till you escape slew mode then the aircraft takes off like a scalded hog.
What other setting needs to be ajusted to correct this? Here.s the contents of the contact points section of the aircraft.cfg file exactly as they appear.
Note that the parts commented out with "//" are the original settings. I did this so that I would be able to get back to the original if needed.

[contact_points]

static_pitch=2.3
static_cg_height=9.2
gear_system_type=1
// 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
point.0= 1, 31.90, 0.000, -9.7, 1000, 0, 1.00, 52, 0.50, 1.00, 0.50, 10.5, 10.5, 0, 152, 152
//point.1= 1, -3.85, -14.000, -9.7, 1500, 1, 1.50, 0, 0.50, 1.00, 0.50, 10.2, 10.2, 2, 152, 152
//point.2= 1, -3.85, 14.000, -9.7, 1500, 2, 1.50, 0, 0.50, 1.00, 0.50, 10.0, 10.0, 3, 152, 152
point.1= 1, -3.85, -14.000, -9.7, 1500, 1, 1.50, 0, 0.50, 1.00, 0.50, 10.2, 10.2, 2, 152, 152
point.2= 1, -3.85, 14.000, -9.7, 1500, 2, 1.50, 0, 0.50, 1.00, 0.50, 10.0, 10.0, 3, 152, 152

point.3=2, 0 , -61.5, 6, 800, 0, 0, 0, 0, 0, 0, 0, 0, 5
point.4=2, 0 , 61.5, 6, 800, 0, 0, 0, 0, 0, 0, 0, 0, 6
point.5=2, -59 , 0, 0, 800, 0, 0, 0, 0, 0, 0, 0, 0, 9
point.6=2, 36.15, 0, 0, 800, 0, 0, 0, 0, 0, 0, 0, 0, 4
 
Now when going into slew mode all seems ok till you escape slew mode then the aircraft takes off like a scalded hog.
When you exit slew mode, the aircraft retains the velocity you created when in slew mode. Before escaping slew mode, either bring the aircraft to a halt, or use World/Map and set the airspeed to something acceptable.
 
Thanks GHD for the info.
Even if the aircraft is parked with engines off and PB set this happens and also even if the aircraft was not actually moved in slew mode. Strange thing is - I just realized that it happens the first time you escape slew mode but not the 2nd time. It seems that every other time this takes place.
 
Before exiting slew mode, check the speed in "World/Map", you may be surprised ;)
 
Hm, as far as I can see, your commented-out points are just the same as your new ones ...

And seeing that vertical distanced is -9.7 for all three, static pitch would more likely to be 0.0. wouldn't it? At any rate that would also explain the tilting fuse in slew.
 
That is correct. Also the static_cg_height should be very close to the main gear's height.

Code:
static_pitch=0.0
static_cg_height=9.7
 
mjahn:
Why the new settings are the same as the commented ones is explained by the fact that I reset all to the original before copy/pasting the contact points into the post - my mistake there

I had the nosegear and maingear set to -10.0 to get the wheels to the proper level - just sitting on the ground

n4gix:
I will reset all and get the static pitch reset to see what happens there.

I thank you both for your input and if this resolves my problem, my hat's off to you both - even though I don't wear a hat!

Will post the results.

Thanks again
 
mjahn and n4gix

My unworn hat is off to you both. Problem is now resolved and furthermore the aircraft no longer exits the hangar (with all doors closed0 like a scalded hog

[contact_points]

static_pitch=0.0
static_cg_height=9.7
gear_system_type=1
// 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
point.0= 1, 31.90, 0.000, -10.2, 1000, 0, 1.00, 52, 0.50, 1.00, 0.50, 10.5, 10.5, 0, 152, 152
//point.1= 1, -3.85, -14.000, -9.7, 1500, 1, 1.50, 0, 0.50, 1.00, 0.50, 10.2, 10.2, 2, 152, 152
//point.2= 1, -3.85, 14.000, -9.7, 1500, 2, 1.50, 0, 0.50, 1.00, 0.50, 10.0, 10.0, 3, 152, 152
point.1= 1, -3.85, -14.000, -10.2, 1500, 1, 1.50, 0, 0.50, 1.00, 0.50, 10.2, 10.2, 2, 152, 152
point.2= 1, -3.85, 14.000, -10.2, 1500, 2, 1.50, 0, 0.50, 1.00, 0.50, 10.0, 10.0, 3, 152, 152


point.3=2, 0 , -61.5, 6, 800, 0, 0, 0, 0, 0, 0, 0, 0, 5
point.4=2, 0 , 61.5, 6, 800, 0, 0, 0, 0, 0, 0, 0, 0, 6
point.5=2, -59 , 0, 0, 800, 0, 0, 0, 0, 0, 0, 0, 0, 9
point.6=2, 36.15, 0, 0, 800, 0, 0, 0, 0, 0, 0, 0, 0, 4

The settings set as indicated in red places the wheels squarely on the ground. Static pitch=0.0 and CG height as shown produce no change in altitude if in flight mode or slew mode.

Thanks
 
Last edited:
static_cg_height=9.7

That should be about right, as it is supposed to be the height of the a/c fully loaded out with weight on wheels.
 
Back
Top