• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA GMAX Keeps Crashing?????

Messages
202
Country
unitedstates
Hey all --

I have a HUGE issue on my hands, that I'm hoping gets sorted out.

As you know, I've been working since April on the Angel 44 model. I'm about ready to start pulling my hair out over this.

I've done the landing gearwell cout outs, the spoilers, just about satisfied with the entire fuselage. The interior's just about finished and ready to go.

All of a sudden, I've been getting a damn "Gmax Has Encountered An Error And Needs to Close" Message, just about as soon as I open the Angel. I just get one mouse click in and it does it.

Thanks for everyone's thought's theories on this. I've been doing texture work, but of course I need a functioning Gmax to complete it.

I'm so worried right now. What happened? Is the file corrupt? Why does it keep doing this? I'm getting ready to scream! If you hear a loud one over where ever you are later today, don't worry, it's probably just me....:(

Thanks in advance for EVERYONE'S help....

P.S. -- Gmax works fine for other models -- just the Angel so far is only when it does it.
 
Try to "Merge" the objects into a new scene. This should filter out whatever is "bad" or "poisoned" in your current saved scene.

If this fails, then "Merge" a few objects at a time into a new scene, until you find a selection that causes the new scene to fail. At that point, you've narrowed down the suspects to "something" within a smaller group of objects.

It's called "divide and conquer..." :cool:
 
If it's not a bad part, this can happen.

When you save the scene, make sure you leave it in wireframe. You might need to lower your gmax display setting, now that your project is larger.

If you save it in smooth mode, it makes a big impact on the pc. Split your project into 2 scenes to avoid any issues. When your finished just make sure not to turn smooth on and put all your scenes into one scene.

DG:speanut:
 
Another tip, don't use the "Prevent Indirect Smoothing" feature of Smooth modifier, if you've done this, for some reason on occassion, it causes a failure when it attempts to do the shading for that surface and fails.

Also, beware of boolean cut meshes, these can generate errors too.

I don't use booleans to cut stuff out anymore, they are too unpredictable and they leave a mess afterwards {Hiroshima}
 
This is usually ALWAYS a material that has become 'corrupt'.

You can usually 'Merge' components out of a corrupt file, groups at a time. Just make note at what groups are which, and which ones corrupt the final file.

I have found that usually the file (Material) that corrupts, will have a blue dot beside it.




Bill
 
Back
Top