• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Mapping Troubles

Hi,

It's because when you apply a UVW Mapping modifier to multiple parts and then use the Gizmo, those numbers only report the scaling for ONE of the parts (usually the smallest one). Therefore, with multiple parts those numbers become pretty useless.

Hope this helps,
 
It may be worth checking the model for scaling problems. This thread may help to spot problems.
 
Apply a Reset Xform to the parts and the problem will be corrected. I don't know why people don't use this tool more often as it can correct most scaling issues. You do have to be careful not to apply it to animated objects or a parent object.
 
Even if I use Reset Xform on both parts (which leaves an Xform modifier on the stacks) and then try the same thing, I get two different sets of numbers when texturing either the large part alone or the large and small part together...
 
Tom was correct the issue only came up when I tried it on a single part. If mapping multiple parts together there isnt an issue. Thanks!
 
Even if I use Reset Xform on both parts (which leaves an Xform modifier on the stacks) and then try the same thing, I get two different sets of numbers when texturing either the large part alone or the large and small part together...
There is a difference between the Xform modifier and the Reset Xform found in the utilities panel. The utilities panel is the one you want to use.
 
I did use the Reset Xform button on the Utilities tab on both parts (individually).
 
How odd, this has always been the cure for me. Now I have had objects that would not rescale properly no matter what I did and I would have to remake them. I just figured it was a Max glitch.
 
Try saving it as a Editable Mesh, then back again to Editable Poly. Sometimes that resets a part, clearing issues. (From Arrimus 3d).

Also, make sure you Reset Scale before Resetting X-Form. If your part suddenly crushes down to a micro dot, you cannot save it. If this should happen, do not save the scene. Exit out without saving, then re-open Max or Gmax and tackle the problem again. If you save before exiting, the part is gone. Always reset Scale before resetting X-Form. Just a heads up. I lost a few parts that way.
 
Try saving it as a Editable Mesh, then back again to Editable Poly. Sometimes that resets a part, clearing issues. (From Arrimus 3d).

Also, make sure you Reset Scale before Resetting X-Form. If your part suddenly crushes down to a micro dot, you cannot save it. If this should happen, do not save the scene. Exit out without saving, then re-open Max or Gmax and tackle the problem again. If you save before exiting, the part is gone. Always reset Scale before resetting X-Form. Just a heads up. I lost a few parts that way.

How are you resetting the scale? I'm not the most knowledgeable Max user but I have not found a way to reset the scale without using the Reset XForm. I made a small test. I made two cubes, one 5m square and one 1m square. I applied an Edit Poly modifier to the 1m cube. Using Select and Uniform Scale I scaled the cube until it was 5m in visual size. Opening object properties showed that it still retained a 1m measurement. I tried reset scale in the Hierarchy tab for both object and then pivot but it still showed 1m in the properties dialog. Once I applied the Reset XForm in the Utilities tab the cube's scale was reset and now the properties dialog displayed a measurement of 5m square. If there is another way of resetting the scale I sure would like to know.
 
Reset Scale is on the Hierarchy tab, same place as Affect Pivot Point Only, together with Reset Transform. Both have their uses, but like Paul I find only Reset XForm (Tools tab) will cure gnarly scaling problems. That tool condenses all operations on the object and gives Max/Gmax an accurate handle on much-mangled geometry. Always save before using it because it won't undo.

Reset XForm resets scale to 1.0 and aligns the pivot to World. Resetting scale first seems unnecessary to me, but who knows with Max/Gmax?
 
I probably clicked some button somehow but in rotation view mode when I click the mouse and move around the aircraft all parts turn to blocks until I release the mouse button. Any way to turn that off?
 
Back
Top