• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Mouse polys blocked

Messages
189
Country
hungary
Hi

I've made a plane, it has two versions, call them model_1 and model_2. There is a "pedestal" panel in the middle of the cockpit, with simple switches on it (battery, alternator, lights and so on). Every switch has a little, completely transparent rectangle above it for mouse clicks.

Also, there is mirror glass inside the cabin with a transparent, reflective poly, it is parented to the sliding canopy.

With model_1 everything works fine. In model_2 every mouse rectangles will be blocked when I export it WITH mirror glass. If the mirror glass is NOT parented to the canopy OR has a basic material (simple gray for example) the mouse rectangles WORKING. If I merge the mirror glass from model_1 (where it is O.K.) it will block the mouse rectangles.

I've made a new part for mirror glass in model_2, mapped it like in model_1 : mouse rectangles blocked again.

Part's scale and X-form reseted, but no success.

Any idea? :eek:
 
In model 2 the mirror glass is between your view and the panel, where in model 1 it is not?
 
No! The pedestal is almost on the floor, at the pilot's leg. The mirror hanging on the canopy, inside the cockpit. Both model is the same configuration, same materials and so on. There is nothing between the switch panel and the eye point.
 
Are your "mouse polygons" using the same Material as the mirror glass? If so, create a new Material for the "mouse polys"...
 
If you are looking at Polygons through their backsides, this will also happen. Check the model to see if you have a poly facing forwards that you do not see from the pilots seat.

Also, if you use a 'head latency device' that follows your head movents, and you lean back and your face is in the seat or rear bulkhead but you do not notice it (its hard to see if you are doing this), then that too causes this.

If you are using FSX instead of P3D and you applied scale to the parts that have 'animations' applied (MouseRects), then you must clear the Scale (reset).

If you are using a Gauge texture 'on' parts that have a MouseRect animation, then the Gauge texture will over-ride the MouseRect of the part. Paper Scissors Stone.. Paper (gauge texture) covers stone (object with code) over-riding the stone...

If you have small 'boxes' that are main Nodes (like Exterior or Cockpit or Interior, or Panel, etc), and they are invisible (invisible texture) and they are hovering in front of your panel, those too will block functionality of objects with embedded code. You can select their Vertices and move them down into the console or floor, then reset their Scale and leave the center where it was (Gizmo) and you will be fine.

* MouseRects have NOTHING to do with Mouse Rectums. Remember this always....
 
I understand everything all you wrote, thanks your answers :) But the two models uses the SAME parts, with the SAME mappings and materials, mouse polys facing upwards, there is nothing between the panel and the eye point, the scale is reseted on them. The mouse rectangles are NOT animated, I use them only for attachpoint because it's easier to "hit" the switches. When I put out the mirror glass from exporting everything works, when put in : not works.
 
Finally I choosed the easier way : I've made a new mirror glass... and it is good :)

Good to hear that you figured it out.

Could I just ask that what aircraft is this that you're working on now, after the release of the Z142? :)
 
Good to hear that you figured it out.

Could I just ask that what aircraft is this that you're working on now, after the release of the Z142? :)

Well...Szevasz ! I'm working on Z-142 1.1 :D

We found some little bugs, one of them was this mirror glass issue. It wasn't "parented" to the canopy, just hanged in the air. I parented it and I thought it is ready, but I was wrong....

Next one ? Did not decided yet, maybe a Moarava ?! Or Turbolet ?! :rolleyes:
 
Well...Szevasz ! I'm working on Z-142 1.1 :D

We found some little bugs, one of them was this mirror glass issue. It wasn't "parented" to the canopy, just hanged in the air. I parented it and I thought it is ready, but I was wrong....

Next one ? Did not decided yet, maybe a Moarava ?! Or Turbolet ?! :rolleyes:

Szia!

Good to hear that you are fixing that mirror thing, it is the only issue i found with the model of the Zlin :)

The Morava and the Let are looking amazing!

Good luck with the projects :)
 
Back
Top