• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Shaking

Messages
246
Country
southafrica
Hi there,

I am working on my Cheetah's Flight dynamics, and I have this problem that when parking brake is on, and I throttle up, the aircraft start shake, until 100% RPM is reached. then the shaking stops. And when I close the throttle, the shaking start again, and sometimes even dont stop at 0% throttle. I have played around with MOI's, engine positions, even brake settings, but no luck. I even replaced the Air file with a complete different aircraft out of desperation. but still no luck. Any idea why this happen?

Oh it is in FS2004

Thanks,

Jakes
 
Last edited:
Hey Jakes, another thing to look at is the contacts points.
The suspension might be having a problem dampening the forces.
But, I'd sort of expect to see other more obvious suspension problems when taxing and such.
Is the suspension working well generally?
Something to try anyway ;)
Danny
 
Last edited:
Hey Jakes, another thing to look at is the contacts points.
The suspension might be having a problem dampening the forces.
But, I'd sort of expect to see other more obvious suspension problems when taxing and such.
Is the suspension working well generally?
Something to try anyway ;)
Danny

Thanks Danny, I will play around with that also. Never thought of that!
 
The shakes are normally a combination of the contact points and the MOI entries in the aircraft.cfg file.

If the MOI (moment of inertia) entries in the aircraft.cfg file are too small for the weight of the aircraft (combination of the empty_weight, fuel weight, and station load weights), the aircraft will shake on the ground. As a test, try increasing them by a significant factor, and observe the outcome. If it does the trick, then start at the original values, and slowly increase them and see if you can resolve the shakes without making the aircraft handling too sluggish in flight (this is the most noticeable effect of increasing the MOIs). You can counteract the sluggishness by increasing the control surface effectiveness numbers in the flight_tuning section of the aircraft.cfg file if necessary.

Good luck. Its solvable.
 
I had this too.

When this happened to my model it was because i had my contact points set too low. My first clue was when I changed model in flight (using alt then change aircraft) my gear would compress to max the minute i switched to my model. If its off by too much you get either a fall to ground or the plane goes up in the air with a flame out. It is possible to have a middle ground where the plane just shakes but if left too long you lose a peice off the airplane. You might let it sit for a minute or two and see if anything falls off....lol
 
left out a few things

The idea i was trying to get across was if you let it sit until something breaks it will tell you where your problem is. when i did this my tail section fell off then my plane died. That narrowed my troubleshotting to the tail section hence i change the static angle and tail wheel y value and the problem was resolved.
 
Back
Top