• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSX Animate...or....Texture?

Messages
1,101
Country
unitedkingdom
Hi folks,

In a bit of a dilemma!

My exterior fuselage is almost complete, minus a few small details, but, do I animate the doors first, or texture them?

Believe I know the most appropriate response, texture first - as in order to texture the fuselage seamlessly, the doors must be re-attached to the fuse, if attached, then I'd likely lose the animations.

Any clarification please?

Thanks.
 
Hi,
well i don't re-attach doors etc when mapping.
I use the technique which is also used for mapping multiple parts with one bitmap.

I actually wrote a tutorial for this some time (6 years :eek: ) ago, which is attached to this post.

Hope this helps!

grt
Willem
 

Attachments

Another way:

1. Clone your animated door.
2. Attach the clone to the fuselage.
3. Texture the fuselage (and the clone)
4. For the Fuselage, Edit Mesh, Element mode.
5. Select the door element (the clone), and Detach.
6. Remove all but one vertex from the original door.
7. Attach the clone door to the original door (now just one vertex).
8. Weld vertices of the door part. (Edit: Later posts say this is not necessary or desired).

Now you have your animated door perfectly mapped.

Thanks to whomever posted this recently. :)

Hope this helps,
 
Last edited:
@Tom,

Interesting idea, one that will prove useful no doubt, thanks for sharing.

@Willem,

Much appreciated, shall have a read through tonight!

Thanks for both response - very much appreciated.
 
Another way:

1. Clone your animated door.
2. Attach the clone to the fuselage.
3. Texture the fuselage (and the clone)
4. For the Fuselage, Edit Mesh, Element mode.
5. Select the door element (the clone), and Detach.
6. Remove all but one vertex from the original door.
7. Attach the clone door to the original door (now just one vertex).
8. Weld vertices of the door part.

Now you have your animated door perfectly mapped.

Thanks to whomever posted this recently. :)

Hope this helps,

I think I did.

And something tells me that the vertex weld is unnecessary and/or not recommended, but I can't remember why.
(The most obvious reason being that you can simply select the door as an element and detach it again without destroying the animation, in case you need to remap it later on or so.)
 
Thanks for clarify that Björn.

I managed to map the fuselage this morning using Tom's method - worked well, but noticed I hadn't cut the front wheel well! Doh!
 
I managed to map the fuselage this morning using Tom's method - worked well, but noticed I hadn't cut the front wheel well! Doh!

If (only *if*) you can live with some stray, unptimized vertices around the cut, just clone the fuselage and boolean cut the opening on one clone and the door(s) on the other clone.

Or do a shape merge as it produces a cut without you having to clone anything beforehand IIRC.
 
Just used the method again and works flawlessly, but another issue!

This is totally different from the scenery design I'm used to.

How'd you get each of the UVW the same scale?

I have cut the fuselage into 4 separate UVW's. Front right, front left, rear left and rear right, but they've all turned out a slightly different scale and the line doesn't match up correctly.

I had a look through Milton's C162 tutorial which was very helpful indeed, but what is the 'correct' method of texturing separate halves of the fuselage on one sheet, so they are all the correct size and line up?

Tris_34.bmp


Hope that doesn't sound too complicated.

Thanks.
 
Simply make certain to use the exact same dimensions for each UVW Map modifier. I determine the size I need, then right click on it to Copy to the buffer. After the next group of polys is selected for mapping, right-click and Paste the UVW Map modifier. Rinse and Repeat for each new polygon group until done.
 
That copy/paste thing never seems to work for me, especially if the front half of the fuselage is very different from the rear half (different vertical dimensions, etc. if it includes the vertical stab, etc). I just need the vertical mapping to be the same, and let me control the horizontal. I don't know of a way to do it in GMAX; hope someone else does - what I need is a constant pixels/foot value.
 
Last edited:
I don't know of a numerical way to do it in GMAX; hope someone else does. If not, that is one advantage of FSDS - you can enter the mapping using numbers.

Simply type in the desired size for the height and width (make sure it's square of course)... :D
 
Thanks Bill. That's worked so far.

What would be your best recommendation for getting all UVW's on 1 texture sheet?
 
Must've been completely asleep when I read this thread last night.

Thanks Williem for the tutorial, I've now got one correctly mapped fuselage using LithUnwrap.

Actual is texture is 2048x2048. In order for the MD3 exporter to work, I've had to detach each section of the fuselage. Is that the correct way?

bn2_fuse.jpg
 
Last edited:
Back
Top