• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FS2004 Bell 429... bending tubes

Messages
1,451
Country
mexico
Hello lads!

Nowadays, I am stuck with the helicopter skids because in FSDS V3.5.1. alongside David Eckert's tutorial (can be found here http://www.daviator.com/tutorial7/FSDSTubeBending_viewlet.html) I can't translate the part axes markings. :confused:

In this tutorial, David freely moves the coordinate axes belonging to a piece with the combination "drag with the mouse, pressing both mouse buttons (left button first)". I understand the logic, however in FSDS V3.5.1. Apparently this function cannot be performed in this program, to carry out the suggestion, it moves the entire piece and not axes (as supposed to be). :banghead:

Would any kind soul can aid me with this issue? :scratchch

Here's the project progress:
Personal_helicopter.jpg


Opsss... this is the right picture
Bending_tube.jpg


In advance, thank you.
Sergio.
 
PROBLEM SOLVED!

Ted

You're the kind soul that came to give me some light!
However, I need to ask: this short cut is not in the help file, so
would you be so kind to point me from where do you know this?
Perhaps there's a lot more "hiden" shortcuts (at least for me!)

It's very interesting and I'm thankful. Again, I'd like to thank for reading this post and helping me.
Here's what I've done with your instructions:

Untitled-1.jpg


Summarizing what David Eckert and Ted teached me:

Bending a tube:
1.- Choose the right dimensions for your tube; for this you need to specify the radius, length, number of points for each cross section and the tube
orientation. In this sample (see the image above) I used:
a) Radius: 5 units (feet or meters depending on your design); length: 20 units; points per section: 16; number of sections: 10. With "n" sections, you'll have
"n+1" cross sections to work.
2.- Once your tube is created, hit the "part mode" button.
3.- Constrain axes as needed; in the image you can appreciate that only I have allowed the coordinate system to be moved in the Z axis.
4.- Then, Hit the "move mode" button to prepare the part to allow the axes movement.
5.- Press and hold [SHIFT], then drag with the left mouse button in the desired direction.
6.- Now you can follow David's tutorial on how to bend tubes with FSDS V3.5.1 (http://www.daviator.com/tutorial7/FSDSTubeBending_viewlet.html)

I hope this may be useful for someone in the future.

Best regards and thank you very much.
Your friend Sergio Kauffman.
:D

P.S. How can I qualify a friend who has helped me? I am aware that in the nickname there's a "point earned bar".
 
Last edited:
However, I need to ask: this short cut is not in the help file, so
would you be so kind to point me from where do you know this?
Perhaps there's a lot more "hiden" shortcuts (at least for me!)
It is located in the help file. Not in the "Shortcut Keys", but in the "Help → Overview → The Basics".
 
Thank you!

Now that I'm in the 3rd. Adam's book, he explain this shortcut. Nowadays I'm struggling with bending the tubes necessary for skids and also with boolean operations to cut my windows... the program start to be a pain in the neck in this regard. I've alligned fuse parts (point by point) and still I can't override errors which supposedly I've made creating them.

Bending_tubes.jpg


Perhaps I shouldn't jumped so quickly into the Adam's books before reading all help files.

Kindest regards,
Sergio.
 
Last edited:
Back
Top