• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Blend Mask Issues

Messages
8
Country
australia
Still working on my airport to be released soon but having
problems with the blend mask. The airport has been placed over a forrest (FTX AU)
which should not be there but with my PR over the top it is partially
see through and shows a flattened green forrset and looks really unrealistic.

Any way to block all landclass under the PR as all I want to see is the PR textures

Thanks
 
Hi,

Why would you use a blend mask if you don't want to see what is under the photo? Without blend mask all you will see is your photo.
 
so i should just ditch the blend mask and remove it from the inf file and recompile it as i don't want to see whats under it but all the Ozx tutorials use blend masks to tell fsx where to sow the pr and default textures together
 
Hi,

Blend mask is often used for a gradual transition from your photo scenery to the default terrain. But in that transition area you would like to see both then. On your airport the blend mask would normally by fully white, so that only your photo is shown at that part.
 
..... with my PR over the top it is partially
see through and shows a flattened green forrset and looks really unrealistic....

This would seem to suggest that you have some non-white in your blendmask source.

The unmasked areas need to be RGB 255,255,255 Absolute White. If they are not, this is just about the only way you will get landclass textures showing through. Also, any value other than white will inhibit autogen annotation in your resampled photoreal image..

A non-masked area will look like a big squre tile, and that will be completely unrealistic. So for realism, you will need a carefully integrated photoreal image. This integration is done with a mask.

Make sure the Blendmask has White, with non-white only for the bits that need to be masked out.
 
Thanks Ian

All the landclass shows through the blend mask
which was made with the lasso tool then inverted with
the outside painted black and the inside PR left showing as per the ozx tutorial.

3652012_7_21_18_33_1_222.jpg
 
Your blend mask should be white on the bits you want to be 100% shown and black on the bits PR that should be 0% shown. It looks like you have grey or the actual image as the blend mask, making it semi transparent. Your blend mask BMP should just black and white/greyscale..... not the actual image on it!
 
The blend mask should be a 24 bit tiff with LZW compression.
 
Last edited:
What Shaun said.

And yes, the blendmask does seem to need to be a TIF file, but does not have to be 8bit (24 bit will do just as nicely)

It does look as though the image is in the blend source. This should not be the case. Also ... NO LAYERS in your TIF file, and no compression.
 
24 bit .bmp works fine for me.... but then I could save a few Mbs and lower the quality.
 
Last edited:
I usually use two layers one for the withe and one for the black msk in PS, though actually ther are the same, but export the photo with two alphachannels, and always work.
 
Remarkable how some stupid question can get one a bit wiser. I always thought it had to be only an 8 bit tif. With a 24 bit, I suppose, you can make the transitions more gradual.
LZW compression, of course, George, because 'no compression' never worked for me, Ian.

Roby
 
As mentioned, blend mask can also just be another channel in your photo geotiff. That's how I usually do it. Same goes for the watermask, then you would have 5 channels in total in your image.
 
You can use LZW compression. However, with large files, resample.exe will run MUCH slower than it does using uncompressed files.

I'm not sure the 24bit files offer any greater resolution, as the RGB info looks to be simply used as 8bit greyscale.

It is just simpler for me to distill this fileset off and then be done with it.
 
Back
Top