• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

P3D v1 Bounding Box, adjusting?

Messages
10,163
Country
us-arizona
Hey all,

How exactly does the Bounding Box work with planes? Is it in Meters? How would one go about adjusting it? If I lower it too much, will it cause crashes when it does touch downs on runways? What happens if its too small? What would that do? Is it centered around the pilot? I notice it has assymetrical entries, not on center. Why would that be?


I am experimenting with it in MCX/Model Tweaker.
 
I can use that as well, but what I mean is how does the Bounding Box function? I have a 'unique' issue and need to know how exactly a bounding box works on a plane. Would it be bottom of the belly to top of the rudder? Would front to rear terminate and center at view point? How does one calculate centers?
 
As far as I have experienced, the bounding box is determined by the first and last vertex on each axis.

Try to create a square plane with an edge length of 300 m each below or above your aircraft, export and load it into FSX. Look at it in the preview window, then load the simulation. You'll see what I mean.
 
Hi,

The bounding box just tells you for each axis between which coordinates your plane is. So the center is the origin you modeled the aircraft around. It doesn't influence any dynamics or crash boxes. Although it influences the drawing of the object (at least for scenery). So a too small bounding box can result in the object appearing too late on screen.
 
As far as I have experienced, the bounding box is determined by the first and last vertex on each axis.

Try to create a square plane with an edge length of 300 m each below or above your aircraft, export and load it into FSX. Look at it in the preview window, then load the simulation. You'll see what I mean.


I was going to start experimenting with it last night. Like I said, its a unique issue. I wanted to figure out or understand why a plane would have a bounding box to begin with, since it already has contact points, etc. Doesn't make sense.
 
I was going to start experimenting with it last night. Like I said, its a unique issue. I wanted to figure out or understand why a plane would have a bounding box to begin with, since it already has contact points, etc. Doesn't make sense.

Collision detection, like ramming your wing into an airport building or another aircraft and stuff like this.
 
Can you adjust the crashbox granularity for a/c like you cAn for scenery models.

This was an undocumented feature when parsing file through xtomdl.exe
 
Collision detection, like ramming your wing into an airport building or another aircraft and stuff like this.

I would have said you were wrong there, as we use 'contact points' for that, (I had thought) but I did run into a building, and it was far away from my wingtip, and my radius is fine. Sooooo.... that must be it, Herr Heretic.
 
At least for scenery the collision detection is done based on the crash box, not on the bounding box. The bounding box is mainly used for quickly testing if an object is on screen.

But not sure if it is the same for aircraft of course...
 
:D

Aren't contact points are only used for the gear or keel?

Scrape points. ;)




At least for scenery the collision detection is done based on the crash box, not on the bounding box. The bounding box is mainly used for quickly testing if an object is on screen.

But not sure if it is the same for aircraft of course...


Roger that. Thanks Arno.
 
Back
Top