• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Changing ILS Ident

Messages
4
Country
us-michigan
Would like to know if there is a way to edit the ILS ident for a runway? KDTW has changed the ident and freqs. for 4L/22R. Changing the freqs was easy enough (using AFX) but no joy with the ident. This is in FS9. Thanks in advance for any help.
 
Would like to know if there is a way to edit the ILS ident for a runway? KDTW has changed the ident and freqs. for 4L/22R. Changing the freqs was easy enough (using AFX) but no joy with the ident. This is in FS9. Thanks in advance for any help.

FS does not allowed the default Ident to be deleted and re-lettered if that is all that changed. We can delete the runway and orphan the stock Localizer. We can renumber the runway and ADE will automatically set up the correct Ident for the new numbered runway but a change to the existing Ident is not the easiest thing to do.

Did by chance KDTW change the number of runway 4L/22R or close that runway?

We could possibly delete the runway 04L/22R which will orphan the existing Localizers and then add back runway 04L/22R with a new Localizer and IDENT.

I have not tried this and Tom is the best person to see what FS9 allows.
 
Last edited:
The numbering remains the same, however there is now an offset on both. 4L is now 037 instead of 035 and 22R is now 212 rather than 215. I would really need some by the hand coaching to make these changes as I have not done this sort of thing before. Looking forward to any help offered.
 
Joe

I will list some steps on how to change the IDENT and Freq. for runway 04L. It is very important that you have a understanding of how ADE works since my steps do not say how to add back a new ILS or other runway code such as start locations.

Open your KDTW (preferably a stock airport that you have not edited with another Utility).

Make sure you know everything needed to add back the same size runway, markings, lights, VASI, etc.

Delete runway 04L/22R. Strong warnings are given about this but delete the stock runway anyway.

Save your .ad2 project file at this point and close ADE. Reopen ADE9 and open your .ad2 airport file. This will make sure we orphan the existing Localizers so we can start with a new runway.

Add new runway 04L/22R with all the proper heading, width, length, markings, lights, etc.

Add a new runway link line (black) down the runway and connect all taxiways.

Add new Start Locations on each end.

Now it is time to add the New ILS's with GS and DME

Select add ILS to rwy 04L and insert the new IDENT and Freq's.

VERY IMPORTANT -- uncheck the check mark that says Create ILS Approach. The approaches for runway 04L/22R already exist in the database and will be picked up with the new 04L/22R runway you add.


Overview-----

What we are doing is deleting the existing stock runway to rid us of the ILS's (orphan to a fake runway) with the wrong IDENT and Freq's.

We rebuild the 04L/22R Runway adding back a new set of ILS's that allow us to insert the new IDENT and freq's.

Important --- The freq's cannot remain the same and the new IDENTS must have new freqs that are different from the stock ones.

hope this is helpful
 
Last edited:
ILS ident

G'day

I just dropped in as i was looking at a fix for manila airport im have using Ninoy Aquino Interational Airport scenery the building end of R6 its the outside the airport one about 9 floors . Every time i try and do a ILS landing i crash into the building yet im about 3m above.... Global texture res very high, sernery complexity extremely dense, autogen extremely dense. I have downloaded Airport Design Editor 9x and have tried to move the ILS with no luck. So will your tips you have given the other poster work for me as well?

I think the GS is out as i have below GS showing and only 1 red light showing at 200 knots and 2 red lights showing 180. Adding some power just before the building i can make it over then i get nose planted in to the runway and i die.
 
G'day

I just dropped in as i was looking at a fix for manila airport im have using Ninoy Aquino Interational Airport scenery the building end of R6 its the outside the airport one about 9 floors . Every time i try and do a ILS landing i crash into the building yet im about 3m above.... Global texture res very high, sernery complexity extremely dense, autogen extremely dense. I have downloaded Airport Design Editor 9x and have tried to move the ILS with no luck. So will your tips you have given the other poster work for me as well?

I think the GS is out as i have below GS showing and only 1 red light showing at 200 knots and 2 red lights showing 180. Adding some power just before the building i can make it over then i get nose planted in to the runway and i die.

Hi Villan

A better fix would be to exclude that tall building since it is in the path of the approach. Google Earth does not show all those buildings on the approach to rwy 06.

Also RWY 06 no longer has the dual T-VASI but replaced them with PAPI4's. both FS9 and FSX have the VASI between the 1st and 2nd taxiway entrances to the runway. Google Earth shows them past the second entrance taxiway. Moving them back to their correct location will
give a higher altitude on approach which will also help to clear the building (if flying visual).

The GS transmitter could move back a few more feet and align with the 2nd taxiway (see Google Earth).
 
Would like to know if there is a way to edit the ILS ident for a runway? KDTW has changed the ident and freqs. for 4L/22R. Changing the freqs was easy enough (using AFX) but no joy with the ident. This is in FS9. Thanks in advance for any help.

Looking at the charts, it appears FAA did NOT change the ILS, but rather added new systems at both runway ends, or maybe at some point they will decommission the old ones?

ILS Z 22R and ILS Z 4L utilize the old equipment JKI/HJI

ILS Y 22R and ILS Y 4L utilize the new equipment ALA/BZB

The localizer for the ALA and BZB are offset, with the courses set as 31.21 and 206.19 (true).

positioning is N42-11-56.26 W083-23-01.93 BZB Z
and N42-13-33.40 W083-21-50.94 ALA Z

I'm assuming this is related to the new simultaneous parallel approach authorized for this runway only 3000 foot separation using a new equipment for PRM-A called ASDE-X.

scott s.
.
 
Looking at the charts, it appears FAA did NOT change the ILS, but rather added new systems at both runway ends, or maybe at some point they will decommission the old ones?

ILS Z 22R and ILS Z 4L utilize the old equipment JKI/HJI

ILS Y 22R and ILS Y 4L utilize the new equipment ALA/BZB

The localizer for the ALA and BZB are offset, with the courses set as 31.21 and 206.19 (true).

positioning is N42-11-56.26 W083-23-01.93 BZB Z
and N42-13-33.40 W083-21-50.94 ALA Z

I'm assuming this is related to the new simultaneous parallel approach authorized for this runway only 3000 foot separation using a new equipment for PRM-A called ASDE-X.

scott s.
.

Scott

That sounds like what KSTL has for their PRM's. If all KDTW did was add 2 new ILS's then ADE will do that. ADE9X is the only Utility that can add double Localizers to any runway. KSTL maintains both sets of localizers which one set is offset. They fly the PRM's only on certain hours of the day.
 
Last edited:
Back
Top