- Messages
- 10,163
- Country

Hey all,
One of my plights in making FS birds have been rounded windows. With Gmax, I was able to do this. Then came the plight for beautifully rounded interior window sill openings (like molded, smooth plastic that has a nice, large radius in it).
This was massively difficult when extruding the interior and having maybe 75 to 100 Vertices in an opening. Trying to Chamfer them becomes a nightmare.
Well, I have been doing something totally new. Thank you God for this technique.
1. Create your normal Cabin. Cut the windows first. Clone the fuselage, make the Cabin an Editable Mesh, flip all polygons inside out. With polygons still selected, on the Extrude section, click 'Local' and extrude the interior inwards. Done.... (regular, nothing different).
2. Hide everything except your Windows. Clone them. Hide the 'real' Windows. Now, take the clone and name them Sills. Select all Polygons and flip them to inward. Leave all polygons selected, 'Local' set on Extrude panel, and Extrude them once. Click on 'Local' on 'Scale' tool and scale them long ways, and then tall ways. You can try scaling them with square Scaler, but they usually go flat or tall, so do this by hand, width then height. Repate this action about 2 times, for a total of three. You are making 'funnels' in a way, (to easily describe it). Now, with the 'face' zone (window surface) of the extrusions still selected, delete it, as you do not need the face zone, only the sides.
3. Again, select all Polygons of the funnels and 'Flip' them (again) so they are facing inwards (inside each other, window Sills are what we are making).
4. Unhide the Cabin. Begin deleting large areas 'around' the windows, including the window openings that are 'in' the Cabin structure. (These were auto created when you extruded the cabin. We have 'new' window openings now, so we are deleting the zones of the windows and will 'graft' these new 'funnels' into place in the Cabin).
Get large areas cut out, and then 'Attach' the funnels (Sills) to the Cabin. Nothing should be touching the Sills.
5. Now, make small Bridges from the cabin to the sills. Each Sill must be 'connected' via a 4 sided Polygon bridge to the Cabin structure. (We attached them, so they are all united, but need bridges now). Next, save as an Editable Poly. Click 'Border' mode, and click on an open 'gap' on a window zone and then click Cap. Repeat until you have 'capped' all the gaping holes around the window Sills.
6. Now, go to Edge mode, click 'Create' and start ironing down the sides by placing Edges like 'bridges' to the Vertices of the Cabin over to the Sills.
A photo speaks a thousand words... so here is what I am talking about..
Works nicely!
Thank you Gerard for telling me how to bridge and how to Cap large area's... and how to 'think' like a Poly.
Bill
One of my plights in making FS birds have been rounded windows. With Gmax, I was able to do this. Then came the plight for beautifully rounded interior window sill openings (like molded, smooth plastic that has a nice, large radius in it).
This was massively difficult when extruding the interior and having maybe 75 to 100 Vertices in an opening. Trying to Chamfer them becomes a nightmare.
Well, I have been doing something totally new. Thank you God for this technique.
1. Create your normal Cabin. Cut the windows first. Clone the fuselage, make the Cabin an Editable Mesh, flip all polygons inside out. With polygons still selected, on the Extrude section, click 'Local' and extrude the interior inwards. Done.... (regular, nothing different).
2. Hide everything except your Windows. Clone them. Hide the 'real' Windows. Now, take the clone and name them Sills. Select all Polygons and flip them to inward. Leave all polygons selected, 'Local' set on Extrude panel, and Extrude them once. Click on 'Local' on 'Scale' tool and scale them long ways, and then tall ways. You can try scaling them with square Scaler, but they usually go flat or tall, so do this by hand, width then height. Repate this action about 2 times, for a total of three. You are making 'funnels' in a way, (to easily describe it). Now, with the 'face' zone (window surface) of the extrusions still selected, delete it, as you do not need the face zone, only the sides.
3. Again, select all Polygons of the funnels and 'Flip' them (again) so they are facing inwards (inside each other, window Sills are what we are making).
4. Unhide the Cabin. Begin deleting large areas 'around' the windows, including the window openings that are 'in' the Cabin structure. (These were auto created when you extruded the cabin. We have 'new' window openings now, so we are deleting the zones of the windows and will 'graft' these new 'funnels' into place in the Cabin).
Get large areas cut out, and then 'Attach' the funnels (Sills) to the Cabin. Nothing should be touching the Sills.
5. Now, make small Bridges from the cabin to the sills. Each Sill must be 'connected' via a 4 sided Polygon bridge to the Cabin structure. (We attached them, so they are all united, but need bridges now). Next, save as an Editable Poly. Click 'Border' mode, and click on an open 'gap' on a window zone and then click Cap. Repeat until you have 'capped' all the gaping holes around the window Sills.
6. Now, go to Edge mode, click 'Create' and start ironing down the sides by placing Edges like 'bridges' to the Vertices of the Cabin over to the Sills.
A photo speaks a thousand words... so here is what I am talking about..
Works nicely!
Thank you Gerard for telling me how to bridge and how to Cap large area's... and how to 'think' like a Poly.
Bill
Last edited:
