• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Faster Startup ?

Messages
26
Country
us-virginia
When checking the results during development of an airport using ADE, much time is time is spent (wasted?) waiting for FSX to restart. Other than removing all but the basic scenery what else can be removed? Aircraft ?(All but one).
How would one set up a dual startup - one full blown and one downsized to minimums needed to check whatever you are working on ?
 
Why are you restarting FSX to see any change(s) from a modification?

Speaking in general terms, I will keep two folder layouts for files while working. One is active and the other inactive. If I make a new BGL file, I copy it into the inactive scenery folder, activate that folder in FSX and inactivate the other "WIP folder". Might take 30 seconds for FSX to rebuild the indexes and reload itself. BINGO, I can see the changes.
 
Okaaay. I'm not quite following you. When I compile an ADEX airport, ADE will not compile the revised airport to a .bgl if FSX is open.
Enlighten me as to how you set up the scenery folders and then tell FSX to rebuild the indexes (indcies?).
 
Most every utility for design work allows you to specify where you want to save your work or compile a BGL file. From there, I use a simple copy and paste to place the revised BGL file into the necessary folder and then do the scenery refresh mentioned above.
 
N N Msg:
Many thanks. I guess you can teach an old dog new tricks after all ! I've been using FSX for over three years and never knew one could refresh/reload the scenery without restartiing FSX.
In fact I had never selected 'Scenery' from the drop down menu. As a holdover from FS9 I had always used an external program to setup my scenery cfg. file (Scenery Config Editor 1.1.1.1).
After reading your post I just happened to click on the 'Scenery' selection and lo and behold when I clicked to close the screen the indexes were refreshed !
Maybe I should RTFM every now and then ! :laughing:
Thanks again !
JMB
 
When making aircraft I pull all the sliders left which certainly makes things load fast. But for scenery design this is not ideal but you can do a few things to speed up the load times.

1. Level of detail radius: small (affects the ground textures in the distance, if you're working on an airport then you don't need to see into the far distance)
2. Texture resolution (reduce this to the minimum you need)
3. Water effect: none (do you really need to see the pretty water?)
4. Weather Cloud detail: Simple
5. Traffic: All off (unless you are checking AI movement).

Don't forget that FSX itself allows you to save and load your settings so you can make one for development and another for normal game use.
 
Hi,
I am very happy finding this thread. I have to think and to thank like Jmbiii and also thanks to Anthony31 for reminding the possibility to save. So I have a work.cfg too.
 
Back
Top