• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA GMax animation problem

Messages
39
Country
unitedkingdom
Hello folks

I'm having a weird problem with control surface animations in GMax. Everything looks normal until I run the animation in GMax. The control surface moves as expected from frame 0 to frame 75, then stays at that point for the last 25 frames. Frame 50 (center of the travel) is not central any more.

In the Motion rollout I notice that when passing frames 0, 25, 50 and 75 both the Position and the Rotation keys are highlit, but at frame 100 only the Position key is.

The ECU levers work fine (0 to 50 frames). Am I right in assuming that control surfaces are animated from 0 to 100 frames?

Any ideas?

Thanks
 
Thanks Bill

You've eliminated one theory!

I still can't think why the last quarter of the 100 frames give no movement and the center point suddenly isn't central any more.

I must be getting something basic wrong.

Could you please "talk" me through the procedure for animating, say, an elevator?

Alan
 
In simple steps...

  1. Delete all existing keys
  2. Rotate* the elevator from neutral to lowest angle down (say 20º)**
  3. Move time slider to frame 50
  4. Press the "ANIMATE" button
  5. Rotate the elevator up 20º to the neutral position***
  6. Move the time slider to frame 100
  7. Rotate the elevator up 20º to the full up position
  8. Press the "ANIMATE" button to turn it OFF
  9. Done!

Notes:
  • *Make sure that the Rotation Tool is set for "Local" and "Pivot Point"
  • **Click on "Angle Snap" on upper toolbar
  • ***Before moving the time slider from frame 50 to frame 100, note that keys have been automatically set for frame 0 and frame 50
 
Last edited:
That's it

Worked like a dream

Many thanks

I must have been doing all my animations wrong right from GMax day 1

Alan
 
Worked like a dream

Many thanks

I must have been doing all my animations wrong right from GMax day 1

Alan

Good! I was hoping that my steps were clear enough while remaining simple to follow.

Now that you know this, here is how you can make "fine tuning adjustments" if necessary...

Suppose that you now discover that the "down elevator" should only be 15º instead of 20º. Instead of starting over and redoing the entire animation...

  1. Click "Angle Snap" ON
  2. Move the time slider to frame 0
  3. Click the "Animation" button ON
  4. Rotate the elevator "up" 5º ("Local" and "Pivot Point")
  5. Click the "Animation" button OFF

Now the elevator will have 20º up and 15º down animation. Note that by default the Angle Snap is set for 5º increments. If you right-click on the Angle Snap button, you can use the popup dialog box to set any desired angle increment.
 
Last edited:
I must tell you. Animations can sometimes go 'arry' (grim, bad, oops, catastrophe' ).

Best thing to do is to delete all the animation points from high back to low (so the part lands back at its original point, no more saved Positions and Rotations), and then quickly and simply reanimate / save / export / test in FS. Just takes about 30 seconds.


I had to reanimate my fuel selectors for the past 3 days. Each new shape had to be redone in animations twice each. :S Happens alot with the FSX SDK.
 
Thanks

Thanks again, you predicted my next question exactly!

I'm sure I could do all this a few years ago but it is amazing how some things get forgotten.

Alan
 
Back
Top