• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

P3D v2 Landing Gear Failure trigger?

Messages
10,163
Country
us-arizona
Hey all,

I want my plane to trigger a crash when one lands it with full wing tanks (tip tanks).

So far I cannot figure a way out to do this. Is there a way to trigger gear failure? I need a way to crash the jet via code when the plane is landed with at least half tanks of fuel in the tip tanks.

Many thanks for any input.


The only failures I can see in the FS9 SDK docs are for electrics failure, hydraulics failure, etc. Nothing to do with wings, landing gear, etc.
 
Why are you looking in the FS9 SDK when you have tagged the subject with P3D? :p

Either way, unless you want to go into simconnect your best choice would be to just trigger raise gear for the side you want the collapse to be when the plane lands with to much fuel in the tip tanks.
 
Last edited:
Hi Bill
problem with using a gauge is its going to be a little bit to absolute :) If it was me Id be playing with the gears crash threshold, I find this setting is nearly always set to high.With a bit of trial and error you may be able to get the gear to fold if the landing isnt greased and or the weight is to high..Im pretty sure in the real world a good pilot should be able to land a overweight aircraft some of the time ;)

Another way could be talk to Tom and see if there is any possibility in plugging into the the failure system via his simvar gauge http://www.fsdeveloper.com/forum/threads/xmltools-v1-0-is-released.430599/
not sure if its doable, pretty sure you can via simconnect though
 

Attachments

  • Clipboard02.jpg
    Clipboard02.jpg
    71.6 KB · Views: 354
Last edited:
Ahh soo.... Many thanks Wozza. Good thinking. I didnt think of making the landing gear weak. That is 'exactly' what happens. Goodness, the answer was right there.

Thanks again.



Bill
 
Why are you looking in the FS9 SDK when you have tagged the subject with P3D? :p

Either way, unless you want to go into simconnect your best choice would be to just trigger raise gear for the side you want the collapse to be when the plane lands with to much fuel in the tip tanks.


Hey Zeiten,

It is for P3D but I use the docs in the FS9 SDK as they are quicker to navigate through rather then the HTM SDK manual. For me anyways.
 
Another way could be talk to Tom and see if there is any possibility in plugging into the the failure system via his simvar gauge http://www.fsdeveloper.com/forum/threads/xmltools-v1-0-is-released.430599/
not sure if its doable, pretty sure you can via simconnect though

Yes of course. Using SIMVARS you can manage the individual position of each one of the landing gear wheels, making this failure simulation very realistic. Fair to say it uses Simconnect to do that.

Tom
 
Back
Top