• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Need halp with animation

Messages
11
Country
us-indiana
I am working on a uh-1 in fsx, and i am using an AI model. how do I animate the tail and main rotors? Please lots of detail in your answers. Thanks.





:confused:
 
Sorry,

I am not an aircraft developer but I do animations for scenery which I think is almost the same...almost...

So I imagine you would just have to animate (rotate) the rotar blades 360 degrees, then animate the rudder left and right... then this is where i will not know but maybe some animation tool you need to tweak each animations on user input for rudder and also adjust the speed of the animation of the rotar matching the RPM - there is also different names you need to use for the FS engine to recognise that it is a rudder and rotar

Not sure if there is a tool that can do this since I am a scenery developer and I use CAT...

So for rotar animations, if you rotated at any speed just 360 degrees, then some sort of tool or ASM tweaks to adjust the speed of that rotar rotation animation to match RPM.... so just speeding up and slowing down one animation

For rudder, well, tweak it so that when user rudder input is center, the animation on the rudder goes to the frame where center is on the animation... then left input, tweak it so it goes to the frame where you animated to the left, same for right input

But again, I could be far off
 
These are all of your main animation keys for helicopters:

Animation Tag ------------Animation Length-Total Keys---Description

Code:
rotor_pitch                100   4 keys = swashplate
rotor_bank                 100   4 keys = swashplate
rotor_droop        REVERSE 100   4 keys = rotor will bend during rotor slow
rotor_blurred              100   4 keys = visibility code for full rpm speed
rotor_slow                 100   4 keys = visibility code for med rpm speed
rotor_still                100   4 keys = visibility code for slow to stopped rpm
rudder_key                 100   3 keys = tail rotor disk angle
lever_pedals_l_r           100   3 keys = VC pedals
lever_stick_l_r            100   3 keys = VC cyclic
lever_stick_fore_aft       100   3 keys = VC cyclic
lever_collective_arm       100   4 keys = VC Collective Handle main rotor disk angle *(DEPENDS ON AIR FILE ...BELL206)
lever_collective_handle    100   4 keys = VC Throttle Handle (use the propeller control axis for joystick)
lever_throttle              50   3 keys = VC Collective Handle main rotor disk angle *(DEPENDS ON AIR FILE .....R22)
rotor_brake                 50   4 keys = Stop rotor quick

This will save you major time..............:yikes:
Sincerely DG
 
Last edited:
how do I animate the tail and main rotors?

Create your main rotor made of 2 duplicate parts and a disk for blurred.
Use the visibility tag for all three rotor sets. Droop can be animated on your still
rotor set. Use the main rotor shaft for animation using rotor_still. Then just link all 3 rotor sets to the main shaft.

So we have 3 sets with vis and a shaft that animates.....:rotfl:

Good luck!
 
I did it again Rich, Thanks for the correction on the swashplate! Hope my list was helpful.
 
Last edited:
If you are creating it as a regular aircraft (i.e. not using the AI Helicopter payware addon), then you can code the rotors exactly the same as you code any other normal aircraft - prop0_still, prop0_slow, and prop0_blurred.

Hope this helps,
 
Back
Top