• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Need help!!

Messages
7
Hi,

i hope that someone can help me with the following problem:

If i export my Plane from GMAX to FS2004, the plane will be located in the ground of the fs (even the gears are down). So the only thing i see is the top of the aircraft, that comes out of the runway.

What is wrong? What do i have to change?

PLEASE help me! THANK YOU



Benny
 
Go to your contact points and set up the Y axis (third dimension setting on the landing gear) and adjust that.

Your plane in Gmax should be located in the center of the screen with the front 'edge' of the wings about 6 inches in front of the X axis (cross wise or lateral axis). That will be your models CG point.


Then just adjust it on the contact points, and also the CG point if needed. Usually only the contact points.


Going into CG is an entirely different story, and deep! later for that one.


EDIT: On CG point (where the center of your model is in the Gmax 'Scene' ), you should technically be able to balance the plane on that point virtually and it could rotate in any direction, perfectly balanced. High wings are usually high, low wings, a big lower, etc.


Bill
 
Last edited:
?

I'm sorry... I really have no idea how to start. Where are the menus in Gmax?
I'm a beginner.

Can you give me an instruction, what to do?

THANKS

Benny
 
Hey Benny,


Contact points are actually in your 'aircraft.cfg' file in your main 'your aircraft' folder.

Open the config file with Windows Notepad, paruse down till you see;

[contact_points]
static_pitch = -1.12
static_cg_height = 3.67
tailwheel_lock = 0
gear_system_type = 0
max_number_of_points = 9

point.0 = 1, 2.50, 0, -3.67, 1500, 0, 0.5, 22, 0.25, 2.5, 0.7, 0, 0, 2, 0, 0
point.1 = 1, -4.45, -4.62, -3.67, 3500, 1, 0.5, 0, 0.3, 2.5, 0.7, 0, 0, 2, 0, 0
point.2 = 1, -4.43, 4.63, -3.67, 3500, 2, 0.5, 0, 0.3, 2.5, 0.7, 0, 0, 3, 0, 0
point.3 = 2, -15.22, -18, -0.2208, 1800, 0, 0, 0, 0, 0, 0, 0, 0, 5, 0, 0
point.4 = 2, -3.90 18.0, 3.00, 1800, 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 6
point.5 = 2,-20.23, 0.0, 0.30, 1800, 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 9
point.6 = 2, 4.6435, 0, -0.5437, 1800, 0, 0, 0, 0, 0, 0, 0, 0, 4, 0, 0
point.7 = 2,-22.80, 0.0, 5.83, 1800, 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 7
point.8 = 2, -4.90, 0.0, -2.00, 1800, 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 8


This is a 'typical' small plane setup for your wheels. The top 3 strings above are the landing gear points. The others are scrape points and things.

Note that the Y (of Z, X, Y settings) is -3.67 and the static CG height is 3.67 also, but opposite, contacts are negatives, but same amount.

Check the red sections and make sure they are correct. Messing around with them will adjust height and things.



But, in Gmax, make sure the front edge of your wing is near the center of the 'scene' or 'world'. Turn on Grid (keyboard = G key) will show you the center of the Scene or World and just align the front edge of your wing to it.

Export, then adjust the settings in the config and you should be good to go.




Bill
 
Last edited:
Hmmm

Hey,

thank you for your help. If i set the contact points, the cg height has to be about 30ft., that the plane is over the ground. Due to this, the cockpit view is so hight, that it's not possible to fly the aircraft.

So, i think i have some thinks to do in gmax, but i don't know what? what is the z=0 line? how can i adjust this?

thanks for you help!!

Benny
 
Hello Benny,

FS doesn't care what your model looks like, it just uses a few numbers to position it in the sim. These include the contact points Bill is referring to.

You need the model's centre positioned like the attached Gmax screenshot. Without the contact points the sim positions your model's centre on the runway. That's what is happening with your model.

The contact points refer to the positions of the wheels (in this case), skids or floats and tell the sim how to position the model on the runway. Get these wrong and the model might well float some way above the ground, so it's just getting these right.

If you're building for FSX, the VC model will also need correctly centred!
Hope this helps!
 

Attachments

  • grid-line.jpg
    grid-line.jpg
    41.2 KB · Views: 391
Reminds me of a model build time, years ago. I could hear it, it was casting a shadow, but I just couldnt find it! Turns out, it was like 30 feet in the air, lol.... I centered the plane, checked the height of landing gear, etc, etc, and it was back to normal. But for a very long day and a night, I couldnt figure out where the plane was! I thought my exports were messed up...

'IT MUST BE GMAX TORTURING MY MIND!!!!' lol....


Bill
 
You...!

no, kidding...

the evil thing. the blue and white checkered, haunted, freaking checkered button thing!
 
It doesn't work

Hi,

thank you very much for your help! It's great!


So, i'm still fighting with the problem:
The aircraft is on the ground if i take these contact points:

cg height =29

and the single contact points are also at a high about -29.

The problem with this height is, that the FS thinks, that the plane big dimensions and its not possible to fly it... The Cockpit view is really 29ft above the ground?!
I have no idea!

Thanks for your answers!

Benny:mad:
 
A screenshot of your model in gmax (say left view, with the Grid turned on) might help to understand what's going on. A centre of gravity 29 feet above the wheels is a socking big plane, maybe an Me-323 Gigant?
 
I wonder if you have made the plane to scale? Is it the proper size in Gmax?


Remember above, my telling you where the grid is on the screen, the cross side (wings axis) of the Scene Grid should be almost in line with the wings leading edge.




Bill
 
Big bird!

For everyone's benefit, here's your screenshot reposted:-




As can be seen, the model's centre in gmax runs through the cockpit windows which from your contact points makes that 29 feet off the ground. Even an Airbus A380 isn't that high off the ground (its cockpit window height is 23 feet or thereabouts) so I'm sure you have a size/scale problem.

I'm not up on commercial jets so I don't know which one you're building: could it be you've used dimensions in feet while gmax is set to use meters? This would make your aircraft too big by a factor of 3.28084 times (roughly).

Oh dear. :(


BTW, although gmax must have its System Unit Scale in meters (or it won't even export to FS), the viewports can be set to display in feet if that makes work easier - it's set from Customize/Units Setup on the gmax menu.
 
Last edited:
interior....

Hi,

i found out, that if i export my model without vc, the plane is in fs on the ground - if i export it with vc, the plane hits the ground...

so, what is wrong with the vc?

does anyone have an idea?

best regards & THANKS

benny
 
Back
Top