• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Need some tips

Messages
4
Hello
Finally i start to model some ww2 airplane in Gmax. So far had some trouble but managed to find solutions, now i'm stuck with some minor problems...

1.I made wing from cylinder than shape so at wing tip is now hole i don't have polygon to slice and fine model wingtip. How to close that hole into polygon, if i chose CAP HOLES i think i don't get poly just i close hole...
2 I mirror wing (i have 2 :P) NOT FROM list not from upper many
( is buggy??) and working fine BUT it's still under left wing under select many .
How to separate copy from original (or mirror copy) i want on select list Left and right wing... or i just have to attach them on fuselage and that's it?
Trying very hard to not post stupid questions :)



Thanks !!!
 
1. CAP the hole as you describe and then use the CUT tool to make some new edges.

2. Make sure your pivot point is at the far most edge of of the wing where the other mirrored part will start.

3. After you have mirrored the wing convert it into an editable poly.
Go into poly mode and select half of the polys and choose detach.
Then you will have 2 parts of the wing.
 
Last edited:
DO NOT USE THE "MIRROR" TOOL ON THE TOP TOOLBAR!!!​

Instead, use the "Mirror" modifier from the stack's rollout.
 
If you right click and 'save object as Editable Poly, then you can go to Border mode, click on the edge (that is open), then click Cap.

After that, while still being an Editable Poly, go to Edge mode and turn on 'Create' and add some Edges (lines) to the endcap you just created.


Later on, you might learn to make a ring, making it the size of the wingtip edge, delete half of it, and weld it to a wingtip edge. Then shape and mold, shape and mold, add some Polygons and Edges, and Voila, a beautiful wingtip is born.

Takes a while to learn all of this. For now, keep it all simple and just learn where the tools are and how to work them. Right now, that is most important.

and have fun! Note, this is very very addictive... :S
 
If you right click and 'save object as Editable Poly, then you can go to Border mode, click on the edge (that is open), then click Cap.

After that, while still being an Editable Poly, go to Edge mode and turn on 'Create' and add some Edges (lines) to the endcap you just created.


Later on, you might learn to make a ring, making it the size of the wingtip edge, delete half of it, and weld it to a wingtip edge. Then shape and mold, shape and mold, add some Polygons and Edges, and Voila, a beautiful wingtip is born.

Takes a while to learn all of this. For now, keep it all simple and just learn where the tools are and how to work them. Right now, that is most important.

and have fun! Note, this is very very addictive... :S

Yep i'm reading and reading Milton's cessna tutorial...But but it's like not
for starters ... so new question :)
After boolean some exhaust holes for exhaust pipes get mess like this.
What i should use to make less polys after Boolean?

Thanks for help :)
 

Attachments

  • hole.jpg
    hole.jpg
    235.4 KB · Views: 492
Before you do your boolean, "frame" the area where they are going to be placed by adding new Edges on either side. This will prevent the boolean from generating those very long and narrow polygons like you see now.
 

Attachments

  • hole.jpg
    hole.jpg
    620.8 KB · Views: 447
Yep i'm reading and reading Milton's cessna tutorial...But but it's like not for starters ...

You really ought to work through the Gmax tutorials supplied with the Gmax help files. Milton doesn't teach you Gmax for beginners, you need to learn how the tools in Gmax work first. Apart from the Gmax P38 tutorial that is - follow that and your aircraft will be wrong way round :mad:.
 
You really ought to work through the Gmax tutorials supplied with the Gmax help files. Milton doesn't teach you Gmax for beginners, you need to learn how the tools in Gmax work first. Apart from the Gmax P38 tutorial that is - follow that and your aircraft will be wrong way round :mad:.

Relax ;P
 
I like to create the wing tips with the line tool, giving you a smooth curves and you can match up the poly's where it meets with the wing so you can weld it. No reason to cap a wing tip....After you make the top view i usually extrude 4 layers and weld. Then i use the scale tool to create rounded edges.

Wing tips get better after you have made a few! Nightmare the first few times!

Good reminder Bill on the mirror tool! nobody wants to find out the upper one is bugged and will make your parts inside out! hehe

My 2 cents:stirthepo
 
Last edited:
i thought of the faster method, if your looking for less work and a low poly's project.

Use the line tool and create a tube for the outer shape of the wing tip and them just delete the inner part of the tube using vertex or polygon. Then move the inner vertex poly's to your outer wing and weld. After 5 minutes of moving and welding you should have a decent looking wing tip!

Of course splines is just the line tool and i use this method that i learned from Lionheart's Spline tutorial. That is the way to go as Mathias mentioned!
 
I too also recommend the Gmax tutorials.

One thing though.. Do them in order. If you jump around, you will be lost, as the tutorials are taught in levels with each level showing you where tools are, which are then relied upon for you to know when you do the next level.

So.... Do level one, then practice what it taught you, and when you have memorized the tools and things of that level, then go to the next level of the tutorial. That is how I finally learned Gmax. I had orginally went straight to the P38 model, but you just cant do it, because the tools are taught on all the lower levels.


The scenery/animation is a bit goofy, by the way, on the Gmax tutorial, unless you are going to be doing those things, but there are tidbits and tools to learn on it, so you need to skim through those levels also. A must.....
 
DO NOT USE THE "MIRROR" TOOL ON THE TOP TOOLBAR!!!​

Isn't the only problem with that the "unflipped" normals?

If so, one can still use it...as long as one flips the normals of the "new", "other" half after mirroring by using an "Edit Mesh" modifier (GMax).
 
Isn't the only problem with that the "unflipped" normals?

If so, one can still use it...as long as one flips the normals of the "new", "other" half after mirroring by using an "Edit Mesh" modifier (GMax).

No, that's just the problem, no amount of faffing around will fix it except to re-apply the Mirror Tool, then add a Mirror modifier to the stack as you should have done to start with...

The problem isn't "flipped normals" at all, it's "inverted normals," that is normals that should sum to a positive 1 value now sum to a -1 value. :eek:
 
The problem isn't "flipped normals" at all, it's "inverted normals," that is normals that should sum to a positive 1 value now sum to a -1 value. :eek:

That sounds to me like nothing more than a simple "inside out problem"... :confused:


In any case, the biggest advantage of the "mirror" modifier is its modifier status...easily removable. :D
 
That sounds to me like nothing more than a simple "inside out problem"... :confused:
Then it's apparent you've never actually tried using it...

It's difficult to explain without having an actual example, but perhaps a word picture will help...

You undoubtedly know that if you have an e-mesh you can tick the "show normals" option in the right pane while in poly select mode. The "normals" will appear as little "arrows" that begin at the skin surface and point in the direction that ambient light will be "reflected." These "normals" have a weighted value that should have a vectored sum between 0 and +1, i.e., they should always be positive.

However, in the case of a Mirrored object, that is one that has been Mirrored using the Tool on the top toolbar, they will have a vectored sum between 0 and -1, they are negative. While visually the "normals" will still show arrows pointing away from the skin surface, really the head of the arrow should be shown as pointing TOWARDS the skin surface, because they are negative normals! This is what causes the "inside out" appearance in the sim. Flipping the normals will not work because it simply shifts the normals to the inside of the skin, without reversing the head of the arrow. Those are still inverted!

The "Mirror" modifier however does not invert the normal's vectors, they will always be positive, which is why it is the correct method to use for FS models.

I hope this will help! :teacher:
 
Good, then all that typing wasn't wasted. Now the simple explanation will make sense also:

  1. Mirror Tool = mirrors both the surface polygons and the normals
  2. Mirror Modifier = mirrors only the surface polygons
 
Back
Top