• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Problem importing DXF in Gmax

Messages
235
Country
ca-ontario
So I have finally restarted on my boat modeling by starting a fresh project and modeling the first piece which I can't take form either my AutoCAD or my other modeling program. When I got that piece done, I went thru the process of creating an .mdl file and brought it into FSX. With all of the other required files in place, I had no problem in opening FSX and having a look at my piece. It works perfectly. Right size, right location.
I then proceeded to import one piece from me other program. This is where I have a problem. my piece comes in at the totally wrong scale. It is roughly 50 times to big. I say roughly because I can't find the dimension of the piece that came in.
Is there a way of taking accurate measurement of the piece and get an accurate location relative to datum lines?

Michel E Paquette
 
Yes, use the Tape helper object:–


PvwJWj.jpg



With careful use of snaps you can get highly accurate results, see the help file for Gmax.
 
Thank you.
I have been looking in all the menus On top nothing seemed significant.
Now I just have to play around with the snap settings

Michel E Paquette
 
If the model already exported to FSX then the system unit is already set to 1 metre. The problem will be units in the .DXF being imported.
 
In Gmax, my units where set right from the start to imperial. And I just checked, in my modeling program the units are also set to imperial. But when I import, Gmax is reading 1 unit of DXF file to be 1 meter instead of 1 inch. I just checked my dxf file and it's the proper size. There has to be a problem with the way Gmax is reading the DXF scaling. Is there a setting somewhere that would govern scaling of imported files? I know there is no scaling option when I am actually importing, but maybe another setting somewhere else maybe?

Michel E Paquette
 
Just check and see what you mean.
Under customize>unit seup, I have imperial, but under preference, system was still metric.
Now I need to see what that will do to my model at the end if I change system to imperial. Get back later

Michel
 
So made a few test this morning and this is what I need to do:
Set units in preference to inches with the "automatic scaling checked on
open the dwg and rescale
do my importing and save dwg and close
open Gmax again and change units in preference back to meters with Automatic scaling still on
Open my dwg and "rescale"
then I can export to mdl

When going thru the airplane tutorial, all they said is to set the unit to metric since FSX reads in metric.
They don't explain anything about the "system units" in preference if you want to detail in imperial.

Unless there is a better way?


Michel
 
To reiterate, to allow the compile the system unit scale must be meters. But after that you can go to Customize/Units Setup and choose any system of measurement you want to *display* in GMAX. I use Decimal Feet, for example. This will NOT change the system unit scale and the object will still compile. And yes, you sometimes must resize imported objects.
 
Last edited:
Yes, you are right. But with all the experimentation I did this morning, I can set my system scale to inches, upscale my model so that all import will be properly size. Then when I want to compile, I close the file, open Gmax and change the system to meters, and when I open the model again, it is shrunk back to proper size to compile to FSX.
Then to continue my model to import, I upsize my model by setting system scale back to inches before opening my dwg

Although if I am not careful I could end up shrinking twice, then it is not visible in FSX.

I feel like I am on the roll again

Michel
 
Back
Top