• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Problems with boolean

Messages
32
Country
denmark
Hello there!

I'm still working with the Cessna 162 tutorial by Milton Shupe.

It is going better and better, but I have a little problem with boolean the window in the door. I have made the door and the rear window, but then I try to boolean the window in the door, it doesn't make the top of the window.

Please see my attached pictures.

That am I doing wrong?:confused:

Regards

Henrik Viking
 

Attachments

  • before_boolean.jpg
    before_boolean.jpg
    73.5 KB · Views: 360
  • after_boolean.jpg
    after_boolean.jpg
    99.8 KB · Views: 434
Davs :)

Are you sure that the operant is completely inside the other part and not just partially?

Sometimes Gmax has difficulties when it comes to boolean with complex parts.
You can detach the polys that you are trying to do the boolean to and see if that helps.

It can also work to reset x-form and scale/transform.
 
Yes, I'm sure the operant is completely inside the other part.

I have as well tried only to select the polygons on the fuselage I want to boolean. It!s still the same ...

Zeiten wrote: "It can also work to reset x-form and scale/transform". How do I do that?

Regards

Henrik Viking
 
To reset Scale and then X-Form, go to the tools window in the right control panel and click on the Hierarchy tab and at the bottom, click Scale to reset scale. I usually click it several times just in case.

Then click the tools tab in the same place, (hammer on the tab). Find Reset X-Form. Click that. Then reset part (collapse stack) back to Editable Poly.


It is good for Boolean operations if both object and Operand are both Editable Poly's. Works better for Gmax.

Make sure that your Operand is similar in sophistication to the E-Poly you are cutting out. Also, if the cut doesnt go well, try moving the Operand over a little bit. Moving it around will have different results. It seems to be a difficult operation for the computer to execute.


I later learned that Booleans are more time consuming to 'repair' and that creating a Spline line as a template in side view (and sometimes top views as well) to use as a cutout template and manually cutting out a really rounded out window is much easier then doing Booleans. To cut a window out, you add Vertices to all the Edges (use Divide mode in Edge mode) to all the Edges that intersect the Template. Then you convert the fuselage to an Editable Mesh and go into Polygon mode and use Divide to insert Vertices along the lines of the Spline Template to cut more Vertices into your fuselage. Next, reset the fuselage into a Ediable Poly (back to Poly again) and now 'create' Edges along the various dots you installed. Voila! Instant window, hand cut, no zillions of extra Vertices and you have exactly the amount of roundness you want, no more being at the mercy of the unstable Boolean operation.


Thats my humble advice. Thats what I use in Gmax.


Bill
 
I have found the solution, or should I say my own error.

After I had made the template to boolean the window in my door, I must have deleted a vertex in the back of the template. I found out that it missed one polygon in the top of the template, and therefore it couldn't made the boolean in the top. See my attachment, if you don't understand that I mean.

Any way, thanks for your advices. Nice to have people like you ... :)

The very best regards

Henrik Viking
 

Attachments

  • boolean.jpg
    boolean.jpg
    55.4 KB · Views: 417
Glad you figured it out.

Boolean was my fave tool for a long while. I grew out of it, but for a long while, I loved it. I usually had to clean up the aftermath quite a bit though when I was done. So many left over, extra Vertices to delete and edit out. :S
 
Back
Top