• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Resolution for building textures?

Messages
64
Country
unitedstates
I was wondering, what do you consider a good resolution for a building model?

On the one hand, taking a hangar that is about 1000' long and mapping it onto a texture that is 512 pixels across looks ok at distance, but close up details become hard to tell. (1/2 pix/ft) On the other hand, it's not feasable to map that same hangar at 120 px/ft, otherwise you'd be looking at a texture sheet that is about 120,000 pixels wide.

Where is the happy medium? What tricks do you have for producing textures that look good both near and far, but aren't ridiculous in size?
 
I was wondering, what do you consider a good resolution for a building model?

On the one hand, taking a hangar that is about 1000' long and mapping it onto a texture that is 512 pixels across looks ok at distance, but close up details become hard to tell. (1/2 pix/ft) On the other hand, it's not feasable to map that same hangar at 120 px/ft, otherwise you'd be looking at a texture sheet that is about 120,000 pixels wide.

Where is the happy medium? What tricks do you have for producing textures that look good both near and far, but aren't ridiculous in size?
Hi jakubz,

In my opinion, it's how you cut up and unwrap your mesh with some crafty repeating textures, commonly referred to as tiled. If it's a small airport you can get away with some nice high detail and use multiple 1K textures per model. Try breaking the hangar up into sections and repeat the ones that are similar.

Are you aiming for a hyper realistic look? This requires a lot fancy modeling techniques and material settings along with a good understanding of textures with alpha channels.

What tools are you using?

Check out this tiled texture: http://www.cgtextures.com/texview.php?id=31252&PHPSESSID=jcr2s7orqj27u8lqqrs32r49u7
 
Last edited:
Hi,

I would also take into account how close you can get with the aircraft to a building. If you can taxi right up to it (like a hangar) I would use a higher resolution texture than when you can't get closer than 100 meter or so, because it is further from the apron.

But for realistic buildings you can get close to it is not weird to use the full with of a 1024 or 2048 pixel texture.
 
Hi jakubz,

In my opinion, it's how you cut up and unwrap your mesh with some crafty repeating textures, commonly referred to as tiled. If it's a small airport you can get away with some nice high detail and use multiple 1K textures per model. Try breaking the hangar up into sections and repeat the ones that are similar.

Are you aiming for a hyper realistic look? This requires a lot fancy modeling techniques and material settings along with a good understanding of textures with alpha channels.

What tools are you using?

Check out this tiled texture: http://www.cgtextures.com/texview.php?id=31252&PHPSESSID=jcr2s7orqj27u8lqqrs32r49u7

The tools are GMax, Paint.net (more comfortable/experienced with) and GIMP (for perspective correction tool). I also am using a Cannon Rebel XSI with a 18-200mm lens to get source photos at 4272x2848 (which is gives me plenty to work with). A smile and nice personality to get along with the airport workers doesn't hurt either. :)

Doesn't tiling require multiple texture files and possibly more polygons? On top of that, can I have multiple textures mapped onto a single object in GMax, or will I have to break up the object? Also, what is the effect on performance?


Hi,

I would also take into account how close you can get with the aircraft to a building. If you can taxi right up to it (like a hangar) I would use a higher resolution texture than when you can't get closer than 100 meter or so, because it is further from the apron.

But for realistic buildings you can get close to it is not weird to use the full with of a 1024 or 2048 pixel texture.

Wait, I thought that the max setting that FSX can handle by default was 1024? I know there is a tweak that you can increase the limit to 2048 or even 4096, but I don't want to force end users to have to rely on that tweak.

For that matter, what is the max texture size that FSX can go to? Has anybody ever tested it?
 
Last edited:
I think nowadays using 2048 or 4096 textures is considered quite normal already. Many users will have the tweak already and modern hardware can run them fine.
 
Back
Top