• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Ribbing 'Definition' Tip

Messages
10,163
Country
us-arizona
Hey all,

I recently got to work on a prestarted model, rebuilding it into FSX technology. I found the work on the model very well done (by Bertrand of XPFR, a French team of simmers that fly in X-Plane).

Bertrand found that you can 'Split' the top ribs on wings to give the ribs an actual, sharp edge. The appearance is brilliant. It works also on runners along the edges of the fuselage.

To make the cut, convert the wing or fuselage or object into an Editable Poly. Select the Edges, such as the tops of the ribs on a wing or runners along the fuselage. Select 'Split' and you are done.

Editable Mesh does not have 'Split' so the object must be an E-Poly.

NOTE: This also works well with cutting lines of cowlings.

Enjoy.... Really makes a great difference. Very nice definition.


Bill
 
Last edited:
The downside is that it doubles the vertices along those seams.
Using different smoothing groups does the same without the negative effects of increased vertex count.
 
Most welcome Tom.

I have never, never had such great, crisp surface edging with Smoothing. This little trick totally impressed me.

I will need to apply this to the Pasped Skylark along the top of the fuselage. I couldnt get it to smooth right and sometimes it looks like tiles on the top instead of longitudinal runner ribs.


Bill
 
Hmm, if you see a difference between this and proper smoothing group assignment you mostly likely did something wrong with smoothing.
 
Gee Bill, no need to get in defense mode.
Quick mockup, one with split edges, the other one only with different smoothing groups.
Tell me which is which, without looking at the file names. ;)
 

Attachments

  • smoothing_groups.jpg
    smoothing_groups.jpg
    8.6 KB · Views: 498
  • split_edges.jpg
    split_edges.jpg
    8.6 KB · Views: 469
My favorite would be chamfered edges though, if poli count is of no concern.
 

Attachments

  • chamfer_edges.jpg
    chamfer_edges.jpg
    9.3 KB · Views: 426
  • chamfer_edges_2.jpg
    chamfer_edges_2.jpg
    285.4 KB · Views: 501
Hey Mathias,

Not in defensive mode. Just smiling and enjoying it all.

I hadnt thought of creating a chamfer along the top and assigning it its own smooth area. Ingenious. I had thought you meant shading the valleys differently, which for me never worked in the past, making the ribbing work nearly invisible unless lighting in FS was just right, from the side, with a good view point.

Mind you, you then have the same identical amount of Vertices as the first technique, but you have a wider area on the top of the rib where on the first route, you have a razors edge. For older planes with wider rib structures, yours would work best.

Thanks for sharing that.



Bill
 
Your first thought was quite correct, Bill, I mean assigning different smoothing groups and that's what you see in pic #1.
It gives the exact same result as using split edges at the benefit of burning less vertices.
Of course one could argue that different smoothing groups are as performance-costly as doubled vertices.
If nothing else you save the extra texture vertices.

#3 and #4 are indeed chamfered edges as the third and IMO visually most appealing option in the mix, but all put together in a single smoothing group.
The benefit of this over the split edge or smoothing group methods in my opinion is that you get a smooth yet well articulated transition from curved to flat surfaces rather than a hard edge where your split edge action ends. The ladder assumes that we decided to spend some extra polys.

EDIT: If you will it's the same effect that was IIRC discussed as the "smooth edge technic" many moons ago over at FFDS, shown below with the box.
Note all polis are in a single smoothing group.
To get an idea what's happening in the box: It's a square box 1m x 1m x 1m.
Each side is beveled respectively extruded by 0.01m one by one and next all polis assigned to smoothing group 1.
The extra line of edges takes care that what otherwise would result in bad shading does not blend into the main surface.
You get a crisp surface with articulated edges, if that makes sense in my crappy English. :-)
 

Attachments

  • smooth_edges.jpg
    smooth_edges.jpg
    13.7 KB · Views: 447
  • smooth_edges_wireframe.jpg
    smooth_edges_wireframe.jpg
    82.4 KB · Views: 510
Last edited:
I think there's a tool for doing that in the 'Mesh Tools' plugin but I've never used it (other than a simple test to see what happened) as I didn't know what it was for. It makes a chamfer but leaves the original geometry intact.
 
I think there's a tool for doing that in the 'Mesh Tools' plugin but I've never used it (other than a simple test to see what happened) as I didn't know what it was for. It makes a chamfer but leaves the original geometry intact.

I remember this one in the toolbar, its the 3 chamfer tool. Normally its two and two, so once you do it once on a standard Chamfer, its doubled the second time. On the MeshTools version, you can do 3 lines in one shot instead of only 2. Very nice option.


Bill
 
Back
Top