• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Specualar and bump map

Messages
246
Country
southafrica
Hi there, I am trying to get my textures working. Tell me quick, whem making textures, for example I have a fuselageL.bmp. Now , for a bump map, I have fuselageL_Bump.bmp, and for specular, I have fuselageL_spec.bmp. DOes all of these bitmaps need to be in your Aircraft texture folder, or not, and how does one use them as DDS texture?

Thanks,

Jakes
 
Um, you don't need those at all! Only one lightmap (Self-Illumination slot) is allowed...
 
Thank you Sir!
SO the bump map is modelled in with Gmax? or how does the Sim read the bump map?

Also, my textures doesn't look that good as I thought on the sim, and I guess somewhere I need to set the size from 1024x1024 to 2048x2048 ?
 
The only thing you put in GMax is the texture's filename!
 
Also, my textures doesn't look that good as I thought on the sim, and I guess somewhere I need to set the size from 1024x1024 to 2048x2048 ?

Hi,

fsx.cfg:
[GRAPHICS]
TEXTURE_MAX_LOAD=2048

Note: Any change in the settings of FSX will set it back to 1024, so you will need to change it again to 2048.

Kai
 
When you export a single 'Diffuse' texture with a FS9 materal (that was brought over into the FSX Gmax system) it will be exported like a FSX material.

/////////////////////////////////////

Specular maps basically will set 'shine' amount. Put that into the Specular Color slot to cause it to reduce shine. (Should be Specular Level, but that will not effect shine there). You can use Specular maps in both Specular Level and Specular Color slots.

I usually have pure black as my Spec map for no shine texture maps.

Speculars, in a nutshell; Bright white equals a bright' shined out white thing. Pure black is normal, no shine, great for flat black and pilots clothing.

//////////////////////////////////////

Good luck on bump maps. I was able to make mine right each time when nVidia came out with their freeware graphics tools for Adobe Photoshop. Install, go to Filters, nVidia tools, select Normal or Bump map creation, and use it on your bump map 'bitmap'.

Its easy to create the 'platform' to make your bumpie from. I create mine from master texture files, like the fuselage. Save as 'fuselage_bump.psd' and create a medium gray layer on top. Then slide over all 3d surfaces on top of that gray layer, so rivets, fuel caps, panel lines, access plates are on top of that gray, visible. Nothing else. (no paint). Now, make 'bumps' white and recessions dark. Dents will be black. Curved edges on indentions or bumps should be smoothed (blurred) so that they 'curve' on their edges or they will be straight. Adjust brightness and darkness to excentuate or tone-down the 'bumpy-ness' factor. Experiment...

Note; when I generate one in Photoshop from a bitmap through the nVidia bump map creator, I then go to Channels, copy the Red channel, create a ALpha channel, paste the Red channel there (actually gray), and then I 'fill' Red channel with pure Black. Blue should be pure white (in Photoshop, it is) and when exporting, make sure Alpha is ticked on, and exported as DDS, and also flip it 'vertically' (do not rotate 180 degrees) and only flip it 'after' you have generated the bump map (must be right side up during the compile mode of bump map generation, 'then' can you flip it).

Note that Bump maps are also called Normal maps. Why?? ack!

//////////////////////////////////////////////


When you get to Plexi, I dont know what to tell you... That is an inigma. Sometimes it will not work right...



Bill
 
Last edited:
Note that Bump maps are also called Normal maps. Why?? ack!

Because that's what they start out being, Bill. The nVidia tool creates a "Normal Map." It has that name because of the way the RGB Channels are structured such that when light strikes the surface at an angle, the resulting vector sum of the "normals" remains 1.0

Because of the way ACES wrote the algorithim for FSX however, you have to cut/paste the Red Channel to the Alpha Channel, leaving the Red Channel pure black, then fill the Blue Channel with pure white...

The sum of the vectors of the Green Channel and the Alpha Channel -as above- are summed such that all normals have a value of 1.0

Now you have a "Bump Map" that FSX will work with!
 
Oh dear have a lot to learn :) will take me sometime to get on track again. Thanks for all the explanations. I like it to understand what I am doing,and not just doing it.
 
Ok, I have textures applied to my model, and when exporting, I select "Use DDS Files" an I have converted my textures to DDS type, but the model is not loading textures in FSX.Where have I gone wrong? Also, no animations are working, although "export animations" are ticked
 
Last edited:
Hey Jakes,

I never tick the 'use DDS textures.' The compiler seems to do that on its own. Try exporting without ticking that and see what happens.


Make sure you have a texture.cfg file in your texture folder in FSX / P3D.


Make sure you have animated things (that are animated) via the Animation Manager. A common mistake when starting out is to forget to include the frames on the Animation Manager. Zero thru 50, zero thru 100, zero thru 200, etc.

If you forgot to assign KF's to animations, then go back, select them, click on the assigned animation so that its up in the window, create KF's (zero thru 100, etc), and then click delete, and then create. You instantly get rid of the old one with no KF's and reassign it the same one again 'with' the KF's.


I still do this by mistake now and then if I am moving too quickly. I forget the addition of the KF's and have to go back and edit, delete, reassign, etc.


Note that now and then, a part will have a wrong assignment, and will sometimes not take a new one. Its a bug. You will need to Merge a new part from an earlier build, replacing it, and then reanimate again. (Just happened to me again the other day).



Bill
 
Back
Top