• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Squirrel cage blower

euroastar350

Resource contributor
Messages
863
Country
us-delaware
Hi guys,

I'm looking for a way to animated and code the cooling fan on a new project, the Robinson R22 Beta II. Engine cooling is supplied by a "squirrel cage" blower which is direct driven by the engine, meaning when the engine starts up, so will the blower. Now my question would be how would I go about animating the blower and what would be the best way to code it so it will start to rotate once the engine starts?
render_03.jpg
 
How deep are you planning to model the electrical/mechanical systems? If you're not going to simulate blower fan failure, then I would take Rick's advice and tag it just like any old rotor.
 
I could animate like a rotor, but it is connected to the engine itself and not the clutch like the rotor is. I could animate it like a rotor, but I want to do custom animations throughout. Failures aren't planned, but it may be a possibility.
 
Can you use the stock propeller animation code?

Fixed wing propeller animation code won't work in helicopter flight models, well at least some.

I did come up with a code, but hasn't been tested just yet.

Code:
<PartInfo>
    <Name>R22_eng_rpm_1</Name>
    <Copy>prop_anim</Copy>
    <AnimLength>100</AnimLength>
    <Visibility>
      <Parameter>
        <Code>
          (A:ENG MAX RPM:1, percent) 6.25 &lt; if{ 1 } els{ 0 }
        </Code>
      </Parameter>
    </Visibility>
    <Animation>
      <Parameter>
        <Sim>
          <Variable>GENERAL ENG RPM:1</Variable>
        </Sim>
      </Parameter>
    </Animation>
  </PartInfo>

  <PartInfo>
      <Name>R22_eng_rpm_2</Name>
        <Copy>prop_anim</Copy>
        <AnimLength>100</AnimLength>
        <Animation>
            <Parameter>
                <Sim>
            <Variable>GENERAL ENG RPM:1</Variable>
          </Sim>
            </Parameter>
        </Animation>
        <Visibility>
            <Parameter>
                <Code>
                    (A:ENG MAX RPM:1, percent) 6.25 &gt;
                    if{
                        (A:ENG MAX RPM:1, percent) 12.5 &lt; if{ 1 } els{ 0 }
                    } els{ 0 }
                </Code>
            </Parameter>
        </Visibility>
    </PartInfo>

    <PartInfo>
        <Name>R22_eng_rpm_3</Name>
        <Copy>prop_anim</Copy>
        <AnimLength>100</AnimLength>
        <Animation>
            <Parameter>
                <Sim>
            <Variable>GENERAL ENG RPM:1</Variable>
          </Sim>
            </Parameter>
        </Animation>
        <Visibility>
            <Parameter>
                <Code>
            (A:ENG MAX RPM:1, percent) 12.5 &gt; if{ 1 } els{ 0 }
                </Code>
            </Parameter>
        </Visibility>
    </PartInfo>
 
If I could suggest; there is going to be extremely little visible distinction with that type of fan for any operating state. It has no spiral indicator and nothing to distinguish it's dimensions beyond a few varieties of gray. In real life, it would be extremely difficult to ascertain any state, beyond running or stationary, with any degree of accuracy and if you take any measures to make this more visible than R/L, it might actually look odd. I should think a rotor0_still and a rotor0_blurred would be a sufficient tipping of the hat to reality.
 
Rick, the blower is direct drive from the engine. If engine is running, so is blower, regardless of rotor rotation.
 
Understood, but it seems like the same applies for the blades. The sprag clutch has to be engaged for autorotation and starting, but there is also a rotor brake to prevent free spinning. The fan housing itself is black or dark gray and the blade assembly is painted black, it appears there may be a white label one some disk portions of the fan assembly so, I suppose it boils down to what is more rewarding for the developer. I think I would be content with an animation that had the label spinning during autorotation.
 
That could be a start. Would I have to use an L var for the squirrel cage?
1. you can do with Lvars, but must consider with multiplayer session.
2. you can copy GENERAL ENG RPM, add condition on it and make a gauge to control the condition. so you have control of the blower to animated.
 
Back
Top