• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSX Tailwheel C_Wheel Animation not functioning

Messages
10,163
Country
us-arizona
Hey all..

yes.. me again.

I have animated my c_wheel tail wheel and finding it only animates in one direction.

Anyone else ever have this issue and how did you repair it?

Animation: 0-100, no animations, 100-200 360 degrees, 90 deg every 25 KF's, clockwise from top.

The animation works fine in right turns, zero turn in left turns. That is the only issue is left turns.


This happened on my Piper Pacer as well. I could never figure this out.

Can it be that the tail wheen (C_Wheel) cannot function right when having set degrees for turning, such as 35 deg max turning? EDIT: No... Tried 180 Deg setting, still will not animate for left turns.


sigh...
 
Last edited:
You may need keyframes more than every 90 degrees for FSX. Also, make sure you have a 0 keyframe.
 
Bill. - Here is the method I use for fs9 models. - Thanks to Robert Sanderson.

CASTORING TAILWHEEL [ By Robert Sanderson }

Set the *.air file section 1101 entry for Cn_dT 'Yaw Moment - Thrust' to 0.018 min.

Set the rotation angle in the [contact_points] section, item 7, of the 'aircraft.cfg' file to 180.0

IN FSDS:-
Make a dummy polygon on the tailwheel rotation (y) axis and lable it c_wheel from the keyframe menu.

Make the tailwheel assembly, strut and fork. Lable it c_gear and define its Parent as c_wheel.

The wheel proper has the standard name of c_tire and a Parent of c_gear.

Animate c_gear using using Keyframes 101 to 200 for compression effects

Animate c_wheel thus:-
Keyframe
100 = Straight. ( 0 degrees, y = fore and aft )

120 = -45 degrees, y, clockwise. (left)

140 = -90 degrees, y, clockwise. (left)

160 = +45 degrees, y, counter clockwise. (right)

180 = +90 degrees, y, counter clockwise. (right)

200 = Straight. ( 0 degrees, y = fore and aft )

------------------------ END -------------------------
 
Have you tried using c_gear instead? I think that is what the DC3 uses for it's tail gear steering arm.

c_tire_blurred + c_tire_still wheel rotation 360 deg rolling animation 0-100 (key frames 0,25,50,75,100)
c_gear wheel steering 360 deg rotating anim 0-200 (key frames 100(-180 deg) 150 (90 deg) 200 (0 deg))

The DC3 example shows no keys for the c_gear animation at frame 0. No keys at frame 0.. just for the steering. keys are 100, 150, 200.

The animation timeline is 0-300.

Hope this helps out. Just realized you're talking about FS9, I'm using the FSX DC3 as the example above, my bad if the anim names are different between the two for I have no idea.
 
Last edited:
We're talking FSX/P3D actually.

Interesting as I didnt know there were this many animation variations for c_wheel.

Another to try. Many thanks, JonP
 
I'm having this same issue with my front wheel steering. I've tried animating a rotation in both directions using the same keyframes as the default DC-3 had. What it would do was always face backwards when in flight, and it would only straighten out when I gave a little bit of rudder to the right. Then when I gave some left rudder, it would stick backwards again. I really hope I can find a solution to this...Could it be something in the aircraft.cfg?
 
When it comes to the nose gear you have 3 different kinds of default variables to deal with.

Code:
    <PartInfo>
        <Name>c_wheel</Name>
        <AnimLength>200</AnimLength>
        <Animation>
           <Parameter>
	<Sim>
            <Variable>GEAR CENTER STEER ANGLE</Variable>
             <Units>percent</Units>
            <Bias>100</Bias>
	</Sim>
           </Parameter>
        </Animation>
    </PartInfo>

Controls the steering angel of the front wheel.
KF 0 is where the wheel has it's full output to the left (seen from behind) and KF 200 is full to the right.
KF 100 is off course the neutral position.

Code:
    <PartInfo>
        <Name>c_gear</Name>
        <AnimLength>200</AnimLength>
        <Animation>
            <Parameter>
                <Sim>
                    <Variable>GEAR ANIMATION POSITION:0</Variable>
                    <Units>keyframe</Units>
                </Sim>
            </Parameter>
        </Animation>
    </PartInfo>

Controls the animation of the gear being extended and retracted.
Suspension is also controlled by this + entries in the aircraft.cfg.
KF 0 is gear fully retracted.
KF 100 is gear fully extended and the suspension fully extended.
KF 200 is suspension fully retracted.

Last one is
Code:
tire_anim

which is off course for the rotation of the wheel it self.
 
Back
Top