• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Tips and tricks needed..

Messages
453
Country
russia
Guys, I was able to animate such as Gears with Bones and IK HI Solvers + Look At Constraints.. damn, I stuck with simple mechanics here.. Just see picture and if somebody willing to have a fun with with this, please help to get it moving.. No matter what program, can be G-Max or 3DS MAX.
Thanks a lot..

Perhaps Just tired..
flap2anim.gif
 
Last edited:
You need to collapse the trajectories to keyframes, then simply tag each moving part with the animation names via the Animation Manager.
 
It should work like this in MAX. For the beginning it doesnt really matter what animation tangent type and names are given.. What I need is to get im properly rigged using Bones, Helpers, Solvers, whatever else...
Like in this Tutorial about sliding Joints.. But this is very long way to get it animated like that, I will comment it on that thread later..

Jim it can be Solidworks or AutoCad or What ever renders the animation.. I Just Found the closest Mechanism that will do the Job for the Aircraft Flaps. Flap Trajectory type is "Fowler" with smell of "Zap" LOL
For the simplicity I could Animate fake, but I need Proper, or at least Proper..



Edgar.
 
Last edited:
I've tried more than once to rig a compley assembly with bones and all, but in the end, I've found it simpler to just keyframe an initial part and then adjust all the other parts in the assembly (by trial & error) until the whole thing moved like it should.

http://www.fsdeveloper.com/wiki/ind...e_application_of_bones_in_aircraft_animations

The railing assembly was just an example that it can be done. I really doubt anyone cares about it when flying the plane in FSX.



My battle plan for the animation:

(Provided part 2 is a long, kinked lever)

sdDA4u5.jpg


Part 1 is a parent of part 2, part 2 is a parent of part 3.*
Part 4 is a parent of part 5.
Pivot points are located where they would be on the real assembly**.

- Rotate part 1, rotate part 2, rotate part 3 so that the flap is pushed out and rotated down to its final position
- Rotate part 4 and part 5 so that no overlapping between parts 4 and 2 occur and so that the end of part 5 is in the roughly correct location on part 3***.


*Depends on where you want to start animating.
**Save part 5 -> part 3.
***If you want to be 99% accurate, put a simple cylinder to where the connector pin would be between part 3 and part 5. Then clone the cylinder and have part 3 be the parent of one clone and part 5 be the parent of the other. When animating part 4 and 5, animate so that the cylinders overlap (nearly) perfectly.

Since animation interpolation is linear, you might need to add some additional keyframes to have each part's animation confined to a more realistic track.


Believe me, albeit being crude, this is the easiest solution before you start messing with constraints, bones and all that other stuff.
 
Oh, Thanks guys for the tips, but I think I found the solution for the "Fowler type flap". Just a short split a second ot the SSJ-100 factory video gave me an excellent idea of how the flap is working on this particular aircraft. Here is my vid from MAX.
I like accuracy..
 
Last edited:
Back
Top