• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA VC panel does not look right

Messages
235
Country
ca-ontario
I have 2 problem with my VC panel.
Here is a snap shot of my panel

panel view.jpg


First problem. I am getting sun reflection on my panel. But when I move my view point to the panel and look back at the sun position, it is behind my roof. Would this be simply because I don't have a texture for my roof yet?
Second problem. Because the surface of my panel is at about 33 degrees from vertical, the figures in my speed gage, my RPM gage and the GPS or distorted. I am guessing that it is because the gauges are set up to be in a vertical position as most planes panel are vertical. How would I go about rectifying this problem? I am kind of puzzled that the directional gage is fine.

Michel E Paquette
 
I have 2 problem with my VC panel.
Here is a snap shot of my panel

View attachment 21211

First problem. I am getting sun reflection on my panel. But when I move my view point to the panel and look back at the sun position, it is behind my roof. Would this be simply because I don't have a texture for my roof yet?

Yes. Its the sun reflecting off of your dash. You are at a odd angle. Move your boat sideways a bit and see if that helps.


Second problem. Because the surface of my panel is at about 33 degrees from vertical, the figures in my speed gage, my RPM gage and the GPS or distorted. I am guessing that it is because the gauges are set up to be in a vertical position as most planes panel are vertical. How would I go about rectifying this problem? I am kind of puzzled that the directional gage is fine.

Some computers and graphics cards have issues with squashing fonts and graphics in gauges. Yours might be doing this. They also will not auto-adjust to face you. If you angle them back, they will appear flat, light graphics. Its something you will have to deal with. For 'dials', you can have gauges that are 3D, a dial that is a part that animates as a gauge. You cannot do this with digital letters and numbers though, of course, including the GPS screen. But with dial gauges, you can, and that cuts down on distortion and you can make the background graphics of the 3D gauges very nice, high resolution.

Michel E Paquette


Answer to question one;

Yes. Its the sun reflecting off of your dash. You are at a odd angle. Move your boat sideways a bit and see if that helps.

Answer to question two;

Some computers and graphics cards have issues with squashing fonts and graphics in gauges. Yours might be doing this. They also will not auto-adjust to face you. If you angle them back, they will appear flat, light graphics. Its something you will have to deal with. For 'dials', you can have gauges that are 3D, a dial that is a part that animates as a gauge. You cannot do this with digital letters and numbers though, of course, including the GPS screen. But with dial gauges, you can, and that cuts down on distortion and you can make the background graphics of the 3D gauges very nice, high resolution.
 
Lionheart
I know that its the sun reflecting on my panel. And once I start turning it does go away. I can see that happening if the sun would be low enough to pass thru my window. But this is happening with the sun up at about 11:00 from the back. Which means that the rays are coming thru my roof. Unless FSX only emits sun rays from the general direction at all angles rather than rays coming from where the sun is?????

For my gauges you are basically saying that if the gauge is 3D, then there should be no problem in tilting the gauge to my panel angle, but with 2D gauges there is not much I can do about it. I will need to have a good look at the Deltasim Gemini GPS since theres appears to be angles and they look fine.

Michel
 
If you are using FSX Materials, make certain in the parameters that you set "No specular bloom", "No Base Material Specular", and set both Reflection Scale and Specular Map Power Scale to zero (sliders full left)
 
Not really. It is a way that should remove the 'glare' from your gauges. Set the above options on your FSX Material for the gauge polys.
 
Thank you Bill
Made the changes and no more reflection.
One problem solved.

On my gauge problem, I guess I will need to do more research later on

Michel
 
Michel, are you certain that your planar map is flat to the angled surface or gauge face? That the gizmo lays flat on the surface. If so, the display should work fine.
 
Milton
I did some checking and as far as I can see my planar screen is parallel to my background and my gizmo is in line with my planar.
I am doing more experimentation tonight to see if redoing my gauge panel vertical will make any difference. I tried to do a bit this morning but I was getting unexpected results.

Michel
 
Milton
I tried a few different thing with my planar. Even reworked my gauge panel to a vertical face, put a new planar face in front and reset the texture. I was still getting my digital scale text tucdked in the corner.

So I decided to extract all the gauge info I needed from the Ultralight, put it into my own subdirectory in my panel folder and went into the XML files to change a few numbers for text location an height.
There is a first time for everything.
Now this is what my panel looks like:

new_Panel.jpg


I still have the arc in the GPS gauge to fix up, but that is going to be much later I think. That is a huge file to go thru to find where that arc is defined.
At the moment I have the 2 GPS at a 15 degreed from vertical, but if I can find which numbers to play with the get all the text right, I would prefer to have them closer to 30 degrees from vertical. If somebody would point me to the the right section to modify the arc, it would be nice
And I also need to work on a background, but that is for far in the future.

Thank you all

Michel E Paquette
 
Back
Top