• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Vitus's mapping wheeze

hairyspin

Resource contributor
Messages
3,253
Country
unitedkingdom
A while back Vitus posted a method of mapping geometry by distorting the mesh with modifiers like Taper, then mapping and UVW Unwrapping before deleting the distorting modifiers.

The effect is to reduce mapping of 3D objects to a single planar map. I've been using this a lot recently in Gmax and for small objects in the VC it's terrific.

This is the bezel of a triple hydraulic gauge about 2½ inches in diameter and I've used the FFD cylindrical modifier to distort the mesh, beginning with a Poly Select to pick out the vertices at the back of the inner rim:-


ffdmapping01.jpg




The FFD cylindrical modifier can now scale these vertices towards the object's centre, making the inner rim properly visible to a planar mapping:-


ffdmapping02.jpg




Repeat the process with other vertices until all the object's polys are visible to a planar mapping and map them all:-


ffdmapping03.jpg




Finally 'switch off' the FFD modifiers - just click on the lightbulb icon next to each modifier in the stack - and the object returns to normal, but with the texture wrapped nicely around all the details. Collapse the stack if you wish.


ffdmapping04.jpg



Note the dimensions for the FFD cylindrical modifier: it's a good idea to match the number of steps around the circumference to the number of steps around the object's circumference to avoid unwanted distortion. The default 4x6x4 dimensions distorted this 40-step bezel as soon as it was applied, so I've used 4x40x4 or similar.

I wouldn't use this to map large objects when I wanted accurate mapping for the texture, but this has simplified a lot of work in my VC.

Cheers, Vitus!! :D
 
Last edited:
Ahem. Cough cough. The cylindrical FFD modifier works very well, but so does the FFD 2x2x2: even simpler is an XForm once vertices have been selected. :o

It's still saved me a lot of hassle. :)


uvwunwrapped.jpg
 
Last edited:
It's a pity I've finished all my gauge mapping otherwise I could have used this! :D

I will bear it in mind if I have to map anything similar though.
 
I did this the other day on my Piper Pacer panel, wrapping the texture around all the sides was brilliant. Replaced the sides back again with the FFD's and Voila. No blurring.


Goodness... I wonder if one could map a fuselage in this manner? Could you imagine flattening out a cylinder (as much as possible) noting all of your scaling amounts, map it, then scale it back??? hmmmmm....

Alot of your lines on the fuselage would then be curved though, as I think about it... Maybe. I'll have to try that.




Bill
 
:eek:
Need to make a note of this...
Nice mapping method this is!!

Will save me a lot work in the future.

grt
Willem
 
Glad you find it useful, gentlemen! :)

I wonder if one could map a fuselage in this manner? Could you imagine flattening out a cylinder (as much as possible) noting all of your scaling amounts, map it, then scale it back???

By all means try it Bill, but I should tell you I used a cylindrical mapping for my fuselage's er, cylindrical shape. Distorting the mesh for a planar map as above is awfully easy to get wrong and on a fuselage you need to keep reasonably accurate for liveries to display correctly.

There was a fair bit of UVW editing even after a Cylindrical mapping to get it sufficiently distortion-free to keep my painter happy. If you want to know how, drop me a PM for the patented Hairy Unwrap(c) with Distortion Check.

The better way of dealing with large objects would be to start working in Max and using its automatic unwrapping tools. Hint hint!
 
The better way of dealing with large objects would be to start working in Max and using its automatic unwrapping tools. Hint hint!

On the other hand, overdependence on the automatic unwrapping can often result in far too much scattering and fragmentation of mapped polygons...

...especially with a virtual cockpit, where every screw head, pushbutton and toggle switch are mapped separately and scattered randomly on the UVW map.

Some manual adjustment to the UVW Map is still required for maximum efficiency.
 
Back
Top