• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Wings, Trailing Edges, Shading Error; Fix

Messages
10,163
Country
us-arizona
Hey all,

I just made a nice little discovery.

If you have a shading error going on with your wing, where the entire back of the wings top and bottom surface are all blackish looking from the smoothing error, here is a quick fix.

* Make sure wing is an Editable Object
* Select the rear Edges of the wing (trailing edge, usually one single Edge along the back),
* Click 'Split'. (Editable Mesh will not have this option).

Done....

Your wings should now look very smooth, top and bottom, no odd shading errors going on.

Thanks to Bertrand for his Edge Splitting technique for ribs which I realized today works also with wing rear trailing edges.



Bill
LHC
 
Great tip. I normally Detach the wing into upper and lower halves, and then Attach them together again. Then I weld the front edge of the wings. This should be much faster. :)
 
Wouldn't it be better in the long run to learn how to use smoothing groups effectively?

I think you're talking about this sort of scenario, not unusual especially when using Auto Smooth (ack!):-


iGiKgShHn9A6C.jpg




Polys on either side of the sharp trailing edge have the same smoothing group and smoothing between surfaces almost completely opposed to each other just doesn't work.


iI8Nxq0H0SKEN.jpg



iCwolgAJX79zm.jpg



ibhPIyHh1PBPAJ.jpg




I hope this shows how the smoothing groups work out on the mesh.

The second-from-last row of polys is given smoothing groups 1 and 2 while the last row on the top of the wing (next to the sharp edge) are given group 2 only. This keeps all the polys on the upper surface smoothed with each other, whereas the under surface is all smoothed with group 1. This breaks the smoothing at the sharp edge and removes the ugly shadowing.

The square edges at the ends of this aileron shape don't need smoothing so I've removed smoothing groups from their polys (or you can use a different group entirely - in this case 3).

Auto Smooth is something I don't like to use, I've never had results I liked from it.
 
Last edited:
Thanks Robert, that was where I learned this from. :)


From the Gmax help files:-

Smoothing groups define whether a surface is rendered with sharp edges or smooth surfaces. Smoothing groups are numbers assigned to the faces of an object. Each face can carry any number of smoothing groups up to the maximum of 32.

If two faces share an edge and share the same smoothing group, they appear as a smooth surface. If they don’t share the same smoothing group, the edge between them renders as a corner.
​
 
Auto Smooth is something I don't like to use, I've never had results I liked from it.
I do use Auto Smooth, but always check carefully for problems like those being discussed.

It's easy enough to fix them, since manual intervention will be required in any case whether one uses Auto Smooth or not... ;)
 
That's great, but the next time I need this I won't be able to find it...
 
Back
Top